Description
This EGW sight mount is a clean, no-drilling way to put a red dot on a pistol that came with an LPA rear sight. Instead of sending a slide off to be milled, you pull the existing LPA rear sight out of its dovetail and slide this mount in its place, then bolt your optic right on top. It's a practical fix for anyone who wants a reflex sight without permanent modifications to the slide.
What the EGW LPA Mount Is Built From
The body is machined from 7075 aluminum and wears a matte black hardcoat finish, so it holds up to real use and keeps a low, non-reflective look on top of the slide. It measures 1.780 inches long and 1.1 inches wide, keeping the footprint tight so your optic sits where it should without hanging over the edges. The hardcoat also resists the kind of wear you'd expect from a part that lives right in the line of fire during racking and handling.
Optics the Trijicon RMR Mount for LPA Fits
This mount is cut for the Trijicon RMR footprint, which covers a wide range of popular red dots. Along with the Trijicon RMR and SRO, it accepts the Holosun HE407C, HE507C, HS407C, and HS507C, as well as Swampfox Kingslayer, Liberty, and Justice sights. That makes it a flexible option if you're deciding between brands or might swap optics down the road.
Getting the EGW Sight Mount Installed
Installation is straightforward. You remove the rear sight, slide the mount into the dovetail from left to right with the muzzle facing forward, and the progressive taper on the dovetail helps it seat snug. From there you set the optic on the mount, add a little blue Loctite to the supplied screws, and torque them down to about 15 inch-pounds. A small trick worth knowing is placing a thin piece of paper between the optic and the mount during install, which keeps Loctite off the sight and makes future removal easier. The kit ships with two 6-32 flat head screws and one 6-32 set screw, so everything you need to mount up is in the package.
Key Specifications
- Manufacturer: EGW (Evolution Gun Works)
- Manufacturer Part Number: 49517
- UPC: 841370116560
- Type: Rear Sight Dovetail Red Dot Mount
- Fits: LPA Rear Sight Dovetail
- Optic Fitment: Trijicon RMR / SRO, Holosun HE407C / HE507C / HS407C / HS507C, Swampfox Kingslayer / Liberty / Justice
- Material: 7075 Aluminum
- Finish: Matte Black Hardcoat
- Color: Black
- Overall Length: 1.780 in
- Overall Width: 1.1 in
- Mounting Direction: Left to right, muzzle facing forward
- Country of Origin: USA
What’s Included
- EGW Trijicon RMR sight mount for LPA
- (2) 6-32 flat head screws
- (1) 6-32 x 3/16 set screw
Frequently Asked Questions
What optics does the EGW Trijicon RMR mount for LPA fit?
This mount uses the Trijicon RMR footprint, so it fits the Trijicon RMR and SRO right out of the box. It also accepts Holosun HE407C, HE507C, HS407C, and HS507C models, along with Swampfox Kingslayer, Liberty, and Justice sights. That gives you plenty of room to pick the optic that works best for you.
Do I need to mill my slide to use this LPA sight mount?
No. This mount installs into the existing LPA rear sight dovetail after you remove the factory rear sight, so there's no machining involved. It's a solid way to run a red dot without permanently altering the slide.
Does the EGW LPA mount come with the screws I need?
Yes, the mounting hardware is included. You get two 6-32 flat head screws for the optic and one 6-32 set screw. EGW recommends a little blue Loctite on the screws and torquing them to around 15 inch-pounds for a secure hold.
What is this EGW sight mount made of?
It's machined from 7075 aluminum and finished in a matte black hardcoat. That combination keeps it lightweight while standing up to the wear and tear a slide-mounted part sees during regular use.





Reviews
There are no reviews yet.