Description
Want to run a red dot on your Smith & Wesson M&P but don't want to send the slide off to get milled? This EGW mount is the clean way to do it. It replaces the factory rear sight by sliding into the existing dovetail, so you get a secure optic platform with no permanent changes to your pistol. Pop the rear sight back in anytime you want and the slide is good as new.
What the EGW DeltaPoint Pro Mount Fits
The business end is built around the Leupold DeltaPoint Pro / Shield RMSc footprint, which opens the door to a wide range of popular optics. Beyond the DeltaPoint Pro itself, it accepts the JPoint, Shield RMS/RMSc/SMS, Redfield Accelerator, Optima, and the Vortex Defender series. On the pistol side, it's cut for the S&W M&P Full Size, M&P 2.0 Full Size, M&P 22 Full Size, M&P Compact, M&P 2.0 Compact, along with the SD9VE and SD40VE. It does not fit the M&P C.O.R.E. series since those already come optics ready, the Shield EZ models, or the M&P .22 Compact. Fitment on the standard M&P Shield can vary by source, so confirm your exact rear sight cut before ordering.
Built Tough and Easy to Run
EGW machines this one from 7075 aluminum and finishes it with a Type III matte black hardcoat anodize, so it shrugs off holster wear and the usual range abuse. At 1.604 inches long and .99 inch wide, it keeps a low, trim profile that doesn't add bulk to the slide. All the mounting hardware comes in the box, including two 6-32 button head screws and a 6-32 set screw.
Installing the S&W M&P Sight Mount
Installation is straightforward if you've got the right tools. Drift out the factory rear sight, slide the EGW mount into the dovetail from left to right with the muzzle pointing forward, snug the set screw if applicable, then seat your optic and lock the screws down with a dab of blue Loctite torqued to 15 in/lbs. A sight pusher tool makes the job a lot easier, and dropping a small piece of paper between the optic and mount keeps Loctite off your red dot during assembly.
Key Specifications
- Manufacturer: EGW (Evolution Gun Works)
- Manufacturer Part Number: 49427
- UPC: 841370113941
- Optic Footprint: Leupold DeltaPoint Pro / Shield RMSc
- Optic Compatibility: DeltaPoint Pro, JPoint, Shield RMS/RMSc/SMS, Redfield Accelerator, Optima, Vortex Defender
- Fits: S&W M&P Full Size, M&P 2.0 FS, M&P 22 FS, M&P Compact, M&P 2.0 Compact, SD9VE, SD40VE
- Mount Type: Rear sight dovetail
- Material: 7075 Aluminum
- Finish: Type III Matte Black Hardcoat Anodized
- Color: Black
- Overall Length: 1.604 in
- Overall Width: 0.99 in
- Torque Spec: 15 in/lbs
- Made In: USA
What’s Included
- EGW DeltaPoint Pro sight mount for S&W M&P
- (2) 6-32 button head mounting screws
- (1) 6-32 set screw
Frequently Asked Questions
Do I need to have my M&P slide milled to use this mount?
No, that's the whole point of it. The EGW mount replaces your factory rear sight and slides into the existing dovetail, so there's no milling or permanent modification to the slide. You can remove it and reinstall your rear sight whenever you want.
Which red dot sights work with this DeltaPoint Pro mount?
It's built for the Leupold DeltaPoint Pro / Shield RMSc footprint. That covers the DeltaPoint Pro, JPoint, Shield RMS/RMSc/SMS, Redfield Accelerator, Optima, and the Vortex Defender series. If your optic shares that same footprint, it'll bolt right up.
Will this fit my M&P Shield?
This mount is cut primarily for the full size and compact M&P frames, the M&P 2.0, M&P 22 Full Size, and the SD9VE/SD40VE. Shield fitment can vary depending on the source and your exact rear sight dovetail, so measure your cut and confirm before ordering. It does not fit the M&P C.O.R.E. series, Shield EZ, or M&P .22 Compact.
What do I need to install it?
A sight pusher tool is highly recommended for drifting out the factory rear sight and seating the mount in the dovetail. The mounting screws take a 5/64 inch hex wrench and the set screw takes a 1/16 inch wrench. Use blue Loctite on the screws and torque them to 15 in/lbs for a secure hold.



Reviews
There are no reviews yet.