Description
The Ruger 10/22 Takedown is built to come apart and go back together, which is great for packing light but tough on an optic trying to keep zero. This EGW rail (part number 46111) is purpose-cut for that rifle, giving you a solid, low-profile one-piece platform that returns to point of aim trip after trip. It's machined from domestic 6061 T6 extruded aluminum and finished in matte silver anodizing, so it shrugs off the knocks that come with a takedown gun living in a pack.
The full-length Picatinny cross slots are the real draw here. You get room to slide rings fore and aft for eye relief, which matters when you're matching a specific scope to your cheek weld. The machined center channel trims weight down to about 2 ounces and, in many setups, keeps the factory iron sights usable underneath. Overall length runs 4.645 inches with a 2.57 inch center spread and a height of roughly 0.4 inches from the top of the receiver to the top of the rail.
Why This EGW 10/22 Takedown Rail Earns Its Keep
Fit is the whole story with a takedown rifle, and this mount is cut to Ruger's receiver spacing so it drops onto the factory holes with no drilling or tapping. It accepts any standard MIL-STD 1913 Picatinny ring, and it'll work with Weaver-style rings too, so your scope, red dot, or thermal choices stay wide open.
Picking 0 MOA for Your Ruger 10/22 Takedown
The 0 MOA rail sits flat with no built-in cant, which is the right call for plinking, small game, and zeroing inside roughly 150 yards. If you're staying at rimfire-friendly distances, flat keeps your scope's elevation centered and your setup simple. The whole thing, hardware and all, is made in the USA.
Key Specifications
- Manufacturer: EGW (Evolution Gun Works)
- MPN: 46111
- UPC: 841370112470
- Fits: Ruger 10/22 and Ruger 10/22 Takedown
- Style: One-Piece Picatinny Rail (MIL-STD 1913)
- Elevation: 0 MOA
- Material: Domestic 6061 T6 Extruded Aluminum
- Finish: Matte Silver Anodized
- Overall Length: 4.645 in
- Center Spread: 2.57 in
- Height: 0.4 in (top of receiver to top of rail)
- Weight: 2 oz
- Ambidextrous: Yes
- Mounting Hardware: #6-48 x 1/4 screws and T-10 bit included
- Torque Spec: 20 in-lbs
- Country of Origin: Made in USA
What’s Included
- EGW Ruger 10/22 Takedown Picatinny rail (silver)
- #6-48 x 1/4 inch mounting screws
- T-10 Torx bit
Frequently Asked Questions
Will this EGW rail hold zero on a Ruger 10/22 Takedown?
Yes, that's exactly what it's built for. The one-piece design is cut to the Takedown's receiver spacing and keeps your optic aligned through repeated breakdown and reassembly. For best results, run a drop of blue Loctite on the screws and torque them to 20 inch-pounds.
What rings do I need with this Picatinny rail?
It uses any standard MIL-STD 1913 Picatinny rings, and Weaver-style rings will work as well. Rings are not included, so you'll want to pick a pair that matches your scope tube diameter and gives you the right height clearance for the objective bell.
Does mounting this rail require drilling or tapping?
No drilling or tapping needed. The rail is drilled to line up with the factory scope mount holes on the 10/22 receiver, so you just remove the existing filler screws or factory base, set the rail in place, and secure it with the included screws and T-10 bit.
What's the difference between the 0 MOA and 20 MOA versions?
The 0 MOA rail sits flat with no forward cant, which is ideal for plinking and shooting inside about 150 yards. The 20 MOA option adds built-in elevation for stretching out to longer rimfire distances. For most 10/22 Takedown use, the flat 0 MOA is the practical choice.




Reviews
There are no reviews yet.