Description
The Remington 660 and 600 Mohawk are handy little carbines, but factory optic mounting on these older guns leaves a lot to be desired. This EGW 0 MOA Picatinny rail fixes that in one clean upgrade. It's a one-piece base machined from domestic 6061 T6 extruded aluminum, drilled to line up with the factory scope holes on your receiver, so there's no drilling or tapping needed to get a modern rail on a vintage rifle.
The full-length Picatinny cross slots are gauged to MIL-STD 1913 specs, which means you get real flexibility in how you set up your rings and dial in eye relief. Run whatever Picatinny or Weaver rings you already own and slide your scope fore and aft until it sits right. The center channel trims weight down to a featherlight 2 ounces, and in a lot of cases the low profile leaves your factory iron sights usable underneath.
Why the 0 MOA Base Makes Sense
EGW recommends the 0 MOA version for most hunting and range work inside 500 yards, which covers exactly what these little Remington carbines were built to do. The 20 MOA option is the one you'd reach for if you were stretching things out past 500 and into the 1000 yard range. For a brush gun or a knock-around deer rifle, zero MOA keeps your scope's adjustment range centered and simple.
Built Tough and Made in the USA
The whole package, from the rail itself down to the mounting screws and wrench, is made in the USA. After machining, these mounts get tumbled, sand blasted, and anodized matte black for a finish that holds up to years of field use. The design carries a bevel on both sides, so it's fully ambidextrous and looks clean from either side of the gun.
Installation is straightforward: snug the screws to around 20 inch pounds of torque with a drip of blue thread locker and you're set. Folks running these on Remington 600 and 660 rifles, including the 6.5mm Magnum variants, consistently report a perfect fit and solid, no-nonsense quality.
Key Specifications
- Manufacturer: EGW (Evolution Gun Works)
- Manufacturer Part Number: 40500
- UPC: 841370105267
- Fits: Remington 660, Remington 600 Mohawk
- Rail Type: One Piece Picatinny
- Elevation: 0 MOA
- Material: Domestic 6061 T6 Extruded Aluminum
- Finish: Matte Black Anodizing
- Center Spread: 3.633 in (distance between the two middle holes)
- Overall Length: 5.882 in
- Height: 0.4 in (top of receiver to top of Picatinny)
- Weight: 2 oz
- Ambidextrous: Yes (beveled both sides)
- Quick Disconnect Ring Compatible: No
- Torque Spec: 20 in/lbs
- Made In: USA
What’s Included
- EGW one-piece 0 MOA Picatinny rail
- #6-48 x 1/4 mounting screws
- T-10 bit
Frequently Asked Questions
Which rifles does the EGW 660/600 Mohawk rail fit?
This base is cut specifically for the Remington Model 660 and the Remington 600 Mohawk, and it lines up with the factory scope mounting holes on the receiver. The bolt pattern also works on the 6.5mm Remington Magnum variants of these guns. EGW suggests measuring the hole spacing on your receiver against the 3.633 inch center spread just to confirm a match before you order.
Do I need to drill or tap my receiver to install this rail?
No. The rail is drilled to use the existing factory scope holes on the 660 and 600 Mohawk, so no gunsmithing is required. Just torque the included screws to about 20 inch pounds with a dab of blue thread locker and you're good to go.
Should I get the 0 MOA or the 20 MOA version?
The 0 MOA version is the right pick for most hunting and shooting inside 500 yards, which suits what these carbines are built for. The 20 MOA option exists for longer range work out to around 1000 yards. For a general-purpose deer or brush rifle, 0 MOA keeps your scope's elevation adjustment centered and easy.
Can I still use my iron sights with this rail mounted?
In many cases, yes. The rail sits at a low 0.4 inch height and features a center channel that keeps the profile slim, so factory iron sights often remain usable underneath. That said, it can depend on your specific sight setup and the rings you choose.




Reviews
There are no reviews yet.