Description
The EGW Remington XP/XR 100, Model 7 3-Hole Short Action rail is a one-piece Picatinny scope base built for shooters who want a rock-solid optic platform on their short action. The 20 MOA of built-in cant tilts your scope forward, which hands back a big chunk of your optic's internal elevation travel. That matters when you start reaching past a few hundred yards and don't want to run out of adjustment while dialing for drop. EGW recommends a 20 MOA base for work in the 500 to 1000 yard range, so this is the version to grab if long distance is part of your plan.
Why the 20 MOA Cant on This EGW Rail Matters
Think of the 20 MOA as free elevation. Instead of burning up your scope's internal adjustment just to get on paper at distance, the angled base does the heavy lifting. A common approach with a 20 MOA mount is zeroing around 200 yards, which leaves you plenty of room to dial up for the far stuff. If most of your shooting lives inside 500 yards, the flat 0 MOA version is the better pick, but for stretching the legs on an XP-100, XR-100, or Model 7, this cant earns its keep.
Build and Fit of the 3-Hole Short Action Base
EGW machines every rail in the USA from domestic 6061-T6 extruded aluminum, then finishes it with a tough Type II matte black anodizing. The center channel is milled out to shave weight, bringing the whole mount in around 2 ounces, and the overall length runs 5.488 inches with a 3.627 inch center spread. It sits roughly .4 inch from the top of the receiver to the top of the Picatinny rail, and it's drilled to line up with the factory scope mount holes on a 3-hole receiver.
Mounting Your EGW Picatinny Scope Base
The full-length Picatinny cross slots let you slide rings front or back to nail down your eye relief, and the rail accepts both Picatinny and Weaver style rings. It's ambidextrous, so lefties and righties are covered equally. EGW calls for 20 inch-pounds of torque on the screws and a drop of blue thread locker to keep everything tight under recoil. One thing worth doing before you order: measure your receiver's hole spacing to confirm you've got the older 3-hole pattern rather than the newer 4-hole layout.
Key Specifications
- Manufacturer: EGW (Evolution Gun Works)
- Manufacturer Part Number: 40202
- UPC: 841370105151
- Fits: Remington XP-100, XR-100, Model 7 Short Action (3-Hole)
- MOA / Cant: 20 MOA
- Rail Type: One-Piece Picatinny
- Ring Compatibility: Picatinny or Weaver
- Material: Domestic 6061-T6 Extruded Aluminum
- Finish: Matte Black Type II Anodizing
- Center Spread: 3.627 in
- Overall Length: 5.488 in
- Height: 0.4 in (top of receiver to top of rail)
- Weight: 2 oz
- Torque Spec: 20 in-lbs
- Ambidextrous: Yes
- Made In: USA
What’s Included
- EGW one-piece Picatinny scope base (20 MOA)
- #6-48 x 1/4 in mounting screws
- T-10 Torx bit
Frequently Asked Questions
Will this EGW rail fit my Remington Model 7?
It's made for the older 3-hole short action receivers on the Remington XP-100, XR-100, and Model 7. The newer rifles use a 4-hole pattern and need a different base. Measure the hole spacing on your receiver before ordering to be sure you've got the 3-hole layout.
Should I get the 20 MOA or the 0 MOA version?
The 20 MOA cant is the pick if you're shooting at longer ranges, roughly 500 to 1000 yards, since it gives back scope elevation travel for dialing drop. If your shooting stays inside about 500 yards, the flat 0 MOA base is the better fit. With a 20 MOA rail, zeroing around 200 yards works well.
What rings work with this scope base?
The rail is a one-piece Picatinny base, so it accepts both Picatinny and Weaver style rings. The full-length cross slots also let you slide the rings forward or back to get your eye relief dialed in. Rings are sold separately.
How do I install the EGW scope rail correctly?
The base drops onto the factory scope mount holes using the included #6-48 screws and T-10 bit. EGW recommends torquing the screws to 20 inch-pounds and adding a drop of blue thread locker to keep them from backing out under recoil.


Reviews
There are no reviews yet.