0
0

L.E. Wilson Steel Neck Sizer Die Bushing .259 (B-259)

UPC: 815145024497

$22.88

2 in stock

Online inventory may differ from in-store availability. 

Fast Shipping

Quick turnaround so you get your gear sooner.

Secure FFL-Friendly Checkout

Trusted checkout with industry-standard protection.

Family-Owned Business

Keeping Traditions Alive Since 1953

Secure Transactions provided with

Description

If you're chasing tighter groups and more consistent bullet seating, dialing in your neck tension is where a lot of the magic happens, and that's exactly what this .259 bushing is built for. L.E. Wilson has been turning out precision reloading gear for decades, and their bushings are a go-to for folks who want to fine-tune how firmly the case neck grips the bullet. This one is marked .259, hardened stainless steel, and carries the B-259 part number.

How the .259 Neck Sizing Bushing Works

Instead of leaning on a traditional expander ball, this bushing sizes the outside of the case neck to the diameter you choose. That means you decide how much squeeze the neck gets, which translates to more uniform neck tension across your loaded rounds. Wilson makes these in .001 inch increments, so you can get right where you want to be. The number stamped on the bushing refers to the middle of the bushing, which is reamed with a slight taper. A handy trick: flipping the bushing so the markings face the case will give you a touch tighter sizing if your brass has work-hardened and started springing back.

Picking the Right .259 Bushing Size

Getting the size right is simple. Measure the outside neck diameter of a loaded cartridge and subtract about .002 to .003 inch, which leaves room for the brass to spring back for proper neck tension. You can also measure your case neck wall thickness, multiply by two, add your bullet diameter, then subtract that same .002 to .003. Both roads get you to the correct bushing.

Fit and Compatibility

This bushing is designed to drop into Wilson neck sizing dies and Wilson bushing-type full length sizing dies. It's made to similar specs as Redding neck bushings and will also fit Redding, RCBS, and Hornady bushing dies. It will not interchange with Forster dies. Made in the USA, it's a small part that makes a real difference in load development.

Key Specifications

  • Manufacturer: L.E. Wilson
  • Bushing Diameter: .259 in
  • Manufacturer Part Number: B-259
  • Material: Hardened stainless steel
  • Size Increments: .001 in
  • Internal Taper: .003 in reamed taper
  • Compatibility: Wilson, Redding, RCBS, and Hornady bushing dies
  • Not Compatible With: Forster dies
  • Country of Origin: Made in USA
  • UPC: 815145024497

What’s Included

  • One L.E. Wilson .259 steel neck sizing bushing (B-259)

Frequently Asked Questions

What dies does the .259 neck sizer bushing fit?

This bushing is made to drop into L.E. Wilson neck sizing dies and Wilson bushing-type full length sizing dies. Because it's built to similar specs as Redding neck bushings, it also fits Redding, RCBS, and Hornady bushing dies. It will not interchange with Forster dies.

How do I know if .259 is the right bushing size for me?

Measure the outside neck diameter of a loaded cartridge and subtract roughly .002 to .003 inch to allow for brass springback. You can also measure your case neck wall thickness, multiply by two, add your bullet diameter, and subtract that same .002 to .003. If that math lands you near .259, this is your bushing.

Does this bushing replace the expander ball?

Yes. The whole point of a bushing-style neck die is that it sizes the outside of the case neck to a set diameter, so you don't need a conventional expander system. That approach gives you more precise neck tension control and works the brass less.

Why would I flip the bushing over?

The size marked on the bushing refers to its middle, which is reamed with a slight taper. Turning the bushing so the markings face the case achieves a slightly tighter size, which comes in handy if your brass has hardened and springs back more, or when you want to fine-tune tension without jumping to the next smaller bushing.

Additional information

UPC

815145024497

Manufacturer

Manufacturer Part Number

B-259

Reviews

There are no reviews yet.

Be the first to review “L.E. Wilson Steel Neck Sizer Die Bushing .259 (B-259)”