0
0

Forster .230″ Neck Bushing (BUSH-230) for Bushing Bump & FL Dies

UPC: 757253998775

$16.99

1 in stock

Online inventory may differ from in-store availability. 

Fast Shipping

Quick turnaround so you get your gear sooner.

Secure FFL-Friendly Checkout

Trusted checkout with industry-standard protection.

Family-Owned Business

Keeping Traditions Alive Since 1953

Secure Transactions provided with

Description

This is the Forster .230" neck bushing, part number BUSH-230, and it's the small but important piece that lets you control exactly how much grip your case neck puts on a bullet. Reloaders chasing tight groups know that neck tension is one of the biggest levers you can pull, and a quality bushing in the right diameter is how you fine-tune it. Forster machines each one to a precise inside dimension, so the .230" marked on this bushing is the inside diameter it sizes your case neck down to.

How the .230" Bushing Fits Into Your Setup

This bushing is made for Forster's Bushing Bump Neck Sizing Dies and Bushing Full Length Sizing Dies. It is not cross-compatible with Redding or L.E. Wilson bushings, so keep it in the Forster family. The general rule of thumb when picking a size is to choose a bushing roughly .002" smaller than your loaded round measures at the neck, though a lot of it comes down to your brass wall thickness and whether you turn your necks. Thicker Lapua or Norma brass, or brass that's been fired several times and work hardened, can change what size you reach for.

Why Forster Neck Bushings Earn Their Keep

Forster bushings are heat treated and honed to the exact inside diameter stated, then run through a cryogenic process that refines and closes the surface of the steel. That extra step is what gives these the reputation for being smooth as silk during sizing, which translates to better looking loaded rounds and less drag on the brass. A cleaner sizing pass means more consistent bullet grip from round to round, and that consistency is what shows up on paper.

Building Out Your Bushing Collection

Forster offers these in .001" increments across a huge range of sizes, so most handloaders end up owning a few around their target diameter to tune for different brass and different stages of case life. The .230" sits in that smaller-caliber range, and having it on the bench gives you the flexibility to adjust neck tension without overworking your brass. Just order by the inside diameter you need and drop it into your die.

Key Specifications

  • Manufacturer: Forster Products
  • Manufacturer Part Number: BUSH-230
  • UPC: 757253998775
  • Inside Diameter: 0.230"
  • Material: Heat treated, cryogenically treated steel
  • Compatibility: Forster Bushing Bump Neck & Bushing Full Length Sizing Dies
  • Size Increments: Available in 0.001" increments
  • Quantity: 1 bushing
  • Country of Origin: USA

What’s Included

  • One Forster .230" neck bushing (BUSH-230)

Frequently Asked Questions

What does the .230" measurement on the Forster neck bushing refer to?

The .230" is the inside diameter the bushing sizes your case neck down to. Forster hones each bushing to that precise inside dimension. When choosing a size, a common starting point is about .002" smaller than your loaded round measures at the neck.

Will this Forster bushing work in Redding or L.E. Wilson dies?

No, this bushing is designed specifically for Forster's Bushing Bump Neck Sizing Dies and Bushing Full Length Sizing Dies. It is not compatible with Redding or L.E. Wilson bushings. Keep it paired with your Forster die for the correct fit.

Why does Forster cryogenically treat these neck bushings?

After heat treating, Forster runs the bushings through a cryogenic process that refines and closes the surface of the steel. The result is an ultra-smooth bushing that sizes case necks smoothly and holds up over a long service life. A smoother bushing also helps produce more consistent loaded rounds.

How do I know if the .230" is the right bushing size for me?

It depends on your brass wall thickness and whether you turn your necks. Measure a loaded round at the neck and generally pick a bushing around .002" smaller, then adjust based on the neck tension you want. Thicker brass or heavily fired, work-hardened brass may call for a different size, which is why many reloaders keep a few sizes on hand.

Additional information

UPC

757253998775

Manufacturer

Manufacturer Part Number

BUSH-230

Reviews

There are no reviews yet.

Be the first to review “Forster .230″ Neck Bushing (BUSH-230) for Bushing Bump & FL Dies”