Description
When you're fitting a stock to an Enfield action, the last thing you want is to chew up the original guard screws running them in and out a dozen times. That's exactly what these Forster Stockmaker's Hand Screws are built to solve. Threaded 1/4"-30 to match the Enfield action, they thread in by hand with a T-style handle so you can seat the barreled action, check your fit, back it out, remove a little wood, and repeat as many times as the job takes.
Where the Enfield Hand Screws Earn Their Keep
Stock inletting and glass bedding are trial-and-error work by nature, and these screws keep the barreled action properly aligned in the stock through every test fit. They're precision made and hardened so they hold up to repeated cycling without stripping or galling. Stockmakers have leaned on tools like these for the final accurate fitting of stock to action because they save your factory hardware and, more importantly, save the stock itself from getting ruined by a sloppy fit.
Bedding an Enfield Sporter with These Screws
A lot of folks reach for these when glass bedding a sporterized 1917 or building up a custom Enfield stock. During bedding they clamp everything down and keep the pillars and action holes indexed together while the epoxy sets. Because military rifles have been sporterized every which way over the years, no single set fits every gun perfectly out of the box. On some builds the takedown screw sits short and the corresponding hand screw needs to be trimmed to length. That's a quick modification, and once done these tools make the whole bedding process far handier than fighting with original screws.
What You Get
This is the Enfield-specific version, sold as a set of two with 3-inch handles. If you've got other actions in the shop, Forster offers matching sets in different thread pitches for Mauser, Winchester 70, Remington 700, Springfield, Ruger 77 and more. For an Enfield project, this is the pair you want in the bench drawer before you open the first tin of bedding compound.
Key Specifications
- Manufacturer: Forster Products
- Manufacturer Part Number: SMENFI
- UPC: 757253005961
- Fits: Enfield action
- Thread: 1/4"-30
- Handle Length: 3 in. (7.6 cm)
- Quantity: Set of 2 (sold in pairs)
- Construction: Precision made, hardened steel
- Handle Style: T-handle
- Use: Stock inletting, trial fitting, glass bedding
What’s Included
- 2 Forster Stockmaker's Hand Screws (Enfield, 1/4"-30 thread)
Frequently Asked Questions
What do the Forster Enfield stockmaker's hand screws actually do?
They let you seat an Enfield barreled action into a stock and pull it back out repeatedly during the fitting process without wearing down your original guard screws. The T-handles thread in by hand so you can check your inlet, remove material, and test again as many times as needed. They also keep the action indexed and clamped in place while glass bedding cures.
Will these fit any Enfield rifle right off the bench?
The 1/4"-30 thread is correct for the Enfield action, so they'll thread in as intended. Because so many Enfields have been sporterized in different ways over the decades, the screw length may sit long or short for your particular build. On some rifles the hand screw needs to be trimmed to match a shorter takedown screw, which is a quick modification and usually the only one required.
Are these sold individually or as a pair?
They come as a set of two, which is what you need since an Enfield action uses front and rear guard screws. Forster sells these in pairs only. The handles measure 3 inches long for good leverage by hand.
Can I use these hand screws for glass bedding as well as inletting?
Yes, they work for both jobs. During inletting they hold the barreled action in alignment while you fine-tune the wood, and during bedding they clamp everything together and keep the pillars indexed to the action holes while the compound sets. Just be sure to release agent the threads well so epoxy doesn't lock them in.



Reviews
There are no reviews yet.