Description
The .32-40 Winchester is one of those classic black powder era cartridges that keeps a loyal following among single-shot and lever-action fans, and getting a good crimp on it matters more than most folks realize. That's where the Lee Precision Factory Crimp Die (part number 91239) earns its spot on your bench. It uses a collet that squeezes the case mouth inward from four sides to lock the bullet firmly in place, giving you a clean, uniform crimp round after round.
What the .32-40 Factory Crimp Die Brings to Your Bench
Unlike a roll crimp die that applies pressure from the top down, this collet design compresses the case mouth from the sides. The big advantage is consistency. It handles minor variations in case length far better than a roll crimp, so you're not fighting inconsistent crimps across a batch of mixed brass. A firmer crimp also builds more start pressure before the bullet moves, which tends to smooth out your pressure curve and tighten up velocity spreads. For a slow, deliberate cartridge like the .32-40, that translates to better consistency downrange.
Why Collet Crimping Works for the .32-40 Winchester
One of the standout traits here is that your bullets don't need a crimp groove or cannelure to get a solid hold. The collet is strong enough to form its own crimp ring, which opens up your options on bullet selection, whether you're running cast, jacketed, or something you poured yourself. If you're loading for a tube magazine lever gun, a proper crimp is key to keeping bullets from backing out under recoil and to keeping rounds chambering smoothly.
Fitment and Setup
This die threads into any standard reloading press with 7/8-14 threads, so it drops right into your existing setup. It's caliber specific to the .32-40 Winchester, meaning there's no swapping or adjusting between cartridges. Setup is done by feel, running a loaded round up and gradually tightening until the collet engages the case mouth. Go slow during setup since it's easy to lean on it too hard. Worth noting, this is a limited production run item, so it's not always sitting on shelves.
Key Specifications
- Manufacturer: Lee Precision
- Manufacturer Part Number: 91239
- UPC: 734307912390
- Cartridge: .32-40 Winchester
- Die Style: Factory Crimp Die (Collet Style)
- Die Type: Single Die
- Thread Size: 7/8-14
- Crimp Method: Collet (squeezes case mouth from four sides)
- Crimp Groove Required: No, collet forms its own
- Country of Origin: United States
- Production: Limited Production Run
What’s Included
- Lee Precision .32-40 Winchester Factory Crimp Die (MPN 91239)
- Instructions
Frequently Asked Questions
Does this .32-40 Winchester Factory Crimp Die fit my press?
Yes, it threads into any reloading press that accepts standard 7/8-14 dies, which covers the vast majority of single-stage and turret presses on the market. It drops right into your existing setup with no adapters needed. Just thread it in, set it up, and you're ready to crimp.
Do my bullets need a crimp groove to use this die?
No. The collet in this die is strong enough to form its own crimp ring on the case mouth, so it works with bullets that have a cannelure or crimp groove as well as those that don't. That gives you plenty of flexibility whether you're loading cast, jacketed, or coated bullets for your .32-40.
How is the Lee Factory Crimp Die different from a roll crimp die?
A roll crimp die applies pressure from the top down, folding the case mouth into the bullet's groove, while this Factory Crimp Die uses a collet that squeezes the case mouth inward from the sides. The collet design is more forgiving of case length variation, so your crimps stay consistent even across mixed brass. It also makes case collapse far less likely on a bottleneck cartridge.
Can I use this die on its own or do I need the full .32-40 die set?
This is a standalone crimp die that runs as a separate step after you've already sized, charged, and seated your bullets. You'll still need a sizing die and a seating die to complete the loading process, which this crimp die is designed to complement. Many loaders prefer crimping as its own operation for better control and more uniform results.


Reviews
There are no reviews yet.