0
0

.35 Remington Collet Neck Sizing Die – Lee Precision 91024

UPC: 734307910242

$22.99

2 in stock

Online inventory may differ from in-store availability. 

Fast Shipping

Quick turnaround so you get your gear sooner.

Secure FFL-Friendly Checkout

Trusted checkout with industry-standard protection.

Family-Owned Business

Keeping Traditions Alive Since 1953

Secure Transactions provided with

Description

Neck sizing is where a lot of handloaders find that extra bit of consistency, and the Lee Precision Collet Neck Sizing Die for .35 Remington is one of the simplest ways to get there. Instead of dragging an expander ball back through the case mouth like a standard die, this one uses a steel collet that squeezes the neck against a precision mandrel. The result is a straight, evenly sized neck with very low runout, which translates to more uniform bullet grip from case to case.

How the .35 Remington Collet Die Earns Its Keep

Because the collet sizes only the neck and leaves the fire-formed body and shoulder alone, your brass stays matched to your chamber. That means less stretching, fewer trips to the case trimmer, and brass that can go many more loadings before it gives up. One thing worth knowing up front: this die is meant for cases that have already been fired through your own rifle. New or once-fired factory brass from another gun should get a full-length pass first before you switch over to neck sizing only.

No Lube, No Mess with the Lee 91024

Since the die is just pressing the neck against the center mandrel, there's no case lubrication required. That's a genuine time saver and cuts out the lube-and-wipe step entirely, plus there's no risk of dented shoulders from trapped lubricant. The decapping pin is built into the mandrel, so cases get deprimed in the same stroke they're sized.

Dialing It In

The trick with any collet die is finding the sweet spot on your press adjustment. A little movement goes a long way, so set it finger tight, run a case, check your neck tension with a bullet, and nudge it down an eighth of a turn at a time until it feels right. And always keep a case in the die when you run the ram, since the collet needs the brass between its fingers and the mandrel to work the way it should. Once you've got it tuned, it repeats beautifully load after load.

Key Specifications

  • Manufacturer: Lee Precision
  • Manufacturer Part Number (MPN): 91024
  • UPC: 734307910242
  • Caliber: .35 Remington
  • Die Type: Collet Neck Sizing Die Only
  • Gun Type: Rifle
  • Sizing Method: Steel collet squeezes case neck against a precision mandrel
  • Case Lube Required: No
  • Decapping: Yes, decapping pin built into the mandrel
  • Thread: 7/8 x 14
  • Material: Hardened steel
  • Country of Manufacture: United States

What’s Included

  • Lee Precision .35 Remington Collet Neck Sizing Die
  • Instruction sheet

Frequently Asked Questions

Do I need to lube my brass with the .35 Remington collet die?

No. This die works by squeezing the neck against a center mandrel, so no case lubrication is needed. That saves you the lube-and-clean step and removes the chance of a lube dent on the shoulder.

Can I use this die with brass fired from another rifle?

It's recommended for brass that has been fired through your own rifle. Neck sizing leaves the case body fire-formed to your chamber, so cases from another gun or new factory brass should get a full-length sizing pass first. After that first firing in your rifle, you can switch to neck sizing only.

Does the Lee collet die decap the case too?

Yes. The decapping pin is built into the mandrel, so the spent primer is knocked out in the same stroke that sizes the neck. You won't need a separate decapping step.

Why choose neck sizing over full-length sizing for .35 Remington?

Neck sizing works the brass less, which generally improves accuracy and can extend case life significantly with less frequent trimming. The collet produces very straight necks with low runout for consistent bullet tension. It's a great fit for handloaders who are reloading brass from a single rifle and want tighter, more uniform ammo.

Additional information

UPC

734307910242

Manufacturer

Manufacturer Part Number

91024

Reviews

There are no reviews yet.

Be the first to review “.35 Remington Collet Neck Sizing Die – Lee Precision 91024”