Description
This is Lee Precision's 379-250-RF double cavity mold, built to cast a .379 diameter 250 grain flat nose bullet that drops right into classic lever gun and single shot chamberings. It's a go-to for folks shooting .375 Winchester and .38/55 WCF who want to roll their own lead at a fraction of what store-bought cast bullets cost. Each pour gives you two bullets, and the design is dialed for the round nose, flat point profile that these old cartridges love.
Why the 379-250-RF Mold Casts So Clean
Lee machines the mold blocks from aluminum, so they heat up and cool down quicker than iron or steel. That means you can usually start dropping good bullets after just a few casts instead of fighting a long warm-up. The cavities are CNC machined for tight roundness and size control, and the tangential cutoff helps keep the sprue clean so you're not dealing with a nib on every base. Aluminum also won't rust, which is a nice bonus if your reloading bench lives in a garage or shop that sees some humidity.
What the 90324 Mold Produces
These bullets run .379 inches in diameter at a nominal 250 grains using Lee's suggested alloy, with an overall length right around .925 inches and a listed ballistic coefficient of .250. The flat nose profile feeds well through tube magazines and does the job on game at the moderate velocities these cartridges are known for. Keep in mind actual weight shifts a little depending on the alloy you're running, which is normal for any cast bullet.
Getting the Most Out of Your Lee Double Cavity Mold
Lee recommends skipping spray mold release and instead smoking the cavities with a wooden match, a beeswax candle, or a butane lighter before your first session. Aluminum blocks are lighter and easier on your arm during long casting runs, but they're softer than steel, so treat them with a little care and they'll hang around for years. Pair it with the right lube and sizing die and you've got a steady supply of bullets for a cartridge that doesn't always have cheap factory options.
Key Specifications
- Manufacturer: Lee Precision
- Manufacturer Part Number: 90324
- UPC: 734307903244
- Mold Designation: 379-250-RF
- Bullet Diameter: .379 inch
- Bullet Weight: 250 Grains (with Lee's suggested alloy)
- Bullet Profile: Round Nose / Flat Nose
- Cavities: 2 (Double Cavity)
- Suggested Cartridges: .375 Winchester, .38/55 WCF
- Bullet Overall Length: .925 inch
- Ballistic Coefficient: .250
- Block Material: CNC Machined Aluminum
- Country of Origin: United States
What’s Included
- Two aluminum mold block halves (379-250-RF double cavity)
- Hardwood handles
- Hard anodized sprue plate
- Instructions
Frequently Asked Questions
What cartridges does the Lee 90324 mold work for?
This mold casts a .379 diameter 250 grain flat nose bullet suited for .375 Winchester and .38/55 WCF. It's a popular choice for lever action and single shot rifles chambered in those rounds. Always check a current reloading manual or powder manufacturer data for load specifics.
Are handles included with this 379-250-RF double cavity mold?
Yes, the mold ships with hardwood handles and a hard anodized sprue plate along with the two aluminum block halves. You'll be ready to attach and start casting out of the box. You will need a separate lube and sizing die if you plan to size and lube your bullets.
Does the aluminum mold need any break-in before casting?
A little. Lee recommends smoking the cavities with a wooden match, beeswax candle, or butane lighter rather than using spray mold release. Aluminum blocks heat up fast, so most casters are dropping good bullets after just a few pours.
Why choose an aluminum mold over iron or steel?
Aluminum blocks won't rust, weigh about a third of what iron or steel molds do, and heat and cool faster for less downtime. That lighter weight also cuts down on fatigue during long casting sessions. Just handle them with care since aluminum is softer than steel.




Reviews
There are no reviews yet.