0
0

Redding Titanium Nitride Neck Sizing Bushing .253 (76253)

UPC: 611760762536

$34.99

1 in stock

Online inventory may differ from in-store availability. 

Fast Shipping

Quick turnaround so you get your gear sooner.

Secure FFL-Friendly Checkout

Trusted checkout with industry-standard protection.

Family-Owned Business

Keeping Traditions Alive Since 1953

Secure Transactions provided with

Description

This is the .253 diameter titanium nitride neck sizing bushing from Redding, part number 76253. It's the piece that lets a bushing-style die do what it does best: size just the neck of your brass down to a precise outside diameter so you get the exact amount of bullet grip you're after. Redding starts with heat-treated steel and adds a titanium nitride surface treatment, which bumps up the surface hardness and cuts down on friction as the brass passes through.

Where the .253 Redding Bushing Fits

These bushings carry the standard Redding footprint, 1/2" outside diameter by 3/8" tall, so they drop right into Redding Type S neck and full-length dies as well as the Competition neck sizing dies. The .253 size lands in the range that works for necks on cartridges like the .223 Remington family and similar small-bore brass, depending on your neck wall thickness. Each bushing is marked with its size so you always know which one is loaded in the die.

Picking the Right Bushing Size

If you're not sure .253 is your number, the method is simple. Seat a bullet in the brass you plan to load, measure the outside neck diameter with a micrometer, then subtract about .001 to .002 to allow for brass spring-back. That gives you the neck tension you want without working the brass harder than necessary. A lot of handloaders keep a few sizes on hand since different brass lots and bullets can shift which bushing runs best.

What the Titanium Nitride Coating Buys You

The TiN treatment is the main reason folks reach for these over the plain steel version. That harder, slicker surface means less sizing effort on the press and reduced drag on the brass, which helps keep things smooth over long reloading sessions. It's a small part that plays a big role in building accurate, repeatable ammo. Made in the USA.

Key Specifications

  • Manufacturer: Redding
  • Manufacturer Part Number: 76253
  • UPC: 611760762536
  • Bushing Diameter: .253 in
  • Type: Neck Sizing Bushing
  • Surface Treatment: Titanium Nitride (TiN)
  • Base Material: Heat-Treated Steel
  • Outside Dimensions: 1/2" OD x 3/8" tall
  • Quantity: 1 Bushing
  • Compatibility: Redding Type S and Competition Dies
  • Country of Origin: USA

What’s Included

  • One (1) Redding .253 titanium nitride neck sizing bushing

Frequently Asked Questions

What dies does the Redding .253 titanium nitride bushing fit?

It fits Redding Type S neck sizing dies, Type S full-length dies, and Redding Competition neck sizing dies. The bushing uses the standard 1/2" outside diameter by 3/8" tall footprint, so it drops right in. It also works in most other dies that accept this common bushing size.

How do I know if .253 is the right bushing size for my brass?

Seat a bullet in the brass you plan to load and measure the outside diameter of the neck with a micrometer. Subtract roughly .001 to .002 from that measurement to account for brass spring-back, and that gives you your bushing size. Measuring several loaded rounds and using the smallest reading is a good habit for consistent neck tension.

What's the advantage of the titanium nitride coating over a plain steel bushing?

The titanium nitride surface treatment increases the effective surface hardness and reduces friction as the case neck passes through. That means less sizing effort at the press and smoother operation over a long loading session. Both versions size the same, but the TiN coating makes the job a little easier on you and the brass.

Does one bushing size the entire length of the neck?

No, a bushing die sizes most of the neck but leaves a small portion unsized near the shoulder, which is just how these dies are machined. You can control how much of the neck gets sized by adjusting the decapping rod and bushing position in the die. This is normal and part of how bushing dies work.

Additional information

UPC

611760762536

Manufacturer

Manufacturer Part Number

76253

Reviews

There are no reviews yet.

Be the first to review “Redding Titanium Nitride Neck Sizing Bushing .253 (76253)”