Description
The Redding .316" steel neck sizing bushing is one of those small parts that makes a big difference at the loading bench. Instead of oversizing your case necks and then relying on an expander ball to pull them back out, a bushing lets you size the neck to exactly the diameter you want in one pass. This is the 73 Style steel version, part number 73316, machined to a .316" inside diameter and built to drop straight into any Redding bushing-style neck sizing or Type S die.
How the .316 Redding Bushing Earns Its Keep
Redding makes these from heat-treated steel with the sizing diameter hand-polished to a surface hardness of Rc 60-62. That hard, slick finish is what keeps sizing effort low and helps the bushing hold its dimension round after round. Picking the right bushing comes down to measuring the neck of a loaded round and subtracting roughly a thousandth of an inch for neck tension, which lets you control exactly how much grip your case has on the bullet. Too little work on the brass means less thinning, longer case life, and better concentricity.
Fitment and Interchangeability
These bushings carry a standard external size of 1/2" O.D. by 3/8" long, so they interchange freely across Redding's bushing-style dies. The whole steel lineup runs from .185" through .368" in .001" increments, and the last three digits of the part number tell you the size. Because the industry sticks to a common bushing dimension, this also plays nicely in dies from other makers that use the same standard. A lot of handloaders keep a few bushings on hand a thousandth apart so they can fine-tune neck tension when chasing accuracy or working with brass that has been fired a few times.
If you already run a Redding neck sizing or Type S die, this is the straightforward way to tune your loads for a particular caliber and brass combination without buying a whole new die.
Key Specifications
- Manufacturer: Redding
- Manufacturer Part Number: 73316
- UPC: 611760733161
- Style: 73 Style Heat-Treated Steel
- Inside Diameter: .316 in
- Surface Hardness: Rc 60-62
- External Dimensions: 1/2" O.D. x 3/8" long
- Material: Hand-polished heat-treated steel
- Quantity: 1 bushing
- Compatibility: Redding bushing-style neck sizing and Type S dies
- Available Size Range: .185 in through .368 in in .001 in increments
What’s Included
- One Redding .316" 73 Style heat-treated steel neck sizing bushing (73316)
Frequently Asked Questions
What dies does the Redding .316 steel bushing fit?
It fits all of Redding's bushing-style neck sizing dies as well as the Type S full-length and neck dies. The bushing uses the standard 1/2" O.D. by 3/8" long dimension, so it interchanges freely across those dies. Because that size is an industry standard, it also works in other brands of bushing dies that use the same spec.
How do I know if .316 is the right bushing size for me?
Measure the neck diameter of a loaded round using calipers or a micrometer, then subtract about .001" to account for brass springback and the grip you want on the bullet. If that math lands you at or near .316", this is your bushing. Many handloaders keep a couple of sizes a thousandth apart so they can fine-tune neck tension.
What's the difference between the steel 73 Style and the titanium nitride bushings?
This is the heat-treated steel version, hand-polished to a Rc 60-62 surface hardness. Redding also offers a titanium nitride version (76 series) that adds a TiN coating to further harden the surface and cut sizing friction. Both are the same size and interchange in the same dies, so it comes down to preference and budget.
Does a neck bushing replace the expander in my die?
In most bushing setups you can size the neck to final dimension with the bushing alone and skip the expander ball. Sizing the neck down in one pass means you work the brass less, which helps with case life and concentricity. Some loaders still run an expander for consistency, so it comes down to how your brass behaves.




Reviews
There are no reviews yet.