Description
This is Redding's .301 diameter steel neck sizing bushing, the simple little part that makes bushing-style dies so handy for precision handloaders. Instead of sizing every neck down more than needed and dragging it back over an expander ball, you pick the exact bushing that gives you the neck tension you're after. The steel here is heat treated and the sizing diameter is hand polished to a surface hardness of Rc 60-62, which keeps sizing effort low and your brass happier over more loadings.
Where the .301 Redding Bushing Fits
These bushings carry the standard Redding external dimensions of 1/2 inch outside diameter by 3/8 inch long, so they interchange freely across all Redding bushing-style neck sizing dies, including Type S and Competition setups. They also play nice with Wilson-style bushings if that's what your setup uses. Each one is clearly marked with its size ID so you always know what's loaded in the die, and Redding offers the full lineup in .001 inch steps from .185 through .368 to cover everything from .17 up to .338 caliber.
Picking the Right Redding Steel Bushing
Sizing a bushing is straightforward once you know the trick. Seat a bullet in the brass you plan to load, measure the outside diameter of the loaded neck with a caliper or micrometer, then subtract .001 to .002 inches for spring-back and bullet grip. That number is your bushing. Most folks find a sweet spot somewhere between .001 and .003 inches of neck tension, so if your loaded round mics at .302 to .303, this .301 lands right in that range. Plenty of reloaders like to keep a bushing on either side of their target so they can experiment with tension while chasing tighter groups.
Redding makes these in the USA, and they've earned their reputation among handloaders who want repeatable results on the bench. One bushing per package, with dies and shellholders sold separately.
Key Specifications
- Diameter: .301 in
- Material: Heat-Treated Steel
- Surface Hardness: Rc 60-62
- Finish: Hand Polished Sizing Diameter
- External Dimensions: 1/2 in O.D. x 3/8 in Long
- Compatibility: All Redding Bushing-Style Neck Sizing Dies (Type S, Competition); interchanges with Wilson-style bushings
- Size Range Offered: .185 in – .368 in in .001 in increments
- Quantity: 1 Bushing
- Origin: Made in USA
- Manufacturer: Redding
- MPN: 73301
- UPC: 611760733017
What’s Included
- One (1) Redding 73 Style .301 steel neck sizing bushing
Frequently Asked Questions
How do I know if the .301 Redding bushing is the right size for my load?
Seat a bullet in the brass you intend to load and measure the outside diameter of the neck with a caliper or micrometer. Subtract .001 to .002 inches from that figure to account for brass spring-back and bullet grip, and that gives you your bushing size. So if your loaded neck mics around .302 to .303 inches, this .301 bushing puts you in the common .001 to .003 inch neck tension range.
Will this bushing work in my Redding Type S or Competition die?
Yes. All of Redding's steel neck bushings share the same 1/2 inch outside diameter by 3/8 inch length, so they interchange freely across every Redding bushing-style neck sizing die, including Type S and Competition models. They'll also fit setups that use Wilson-style bushings.
What's the difference between the steel bushing and the titanium nitride version?
Both are heat-treated steel hand-polished to Rc 60-62 hardness and size your necks exactly the same way. The titanium nitride bushings add a surface coating that bumps up hardness a bit more and reduces sizing friction, which some handloaders prefer for easing stress on brass. The plain steel .301 here does the job for the vast majority of reloaders and is the most popular choice.
Does the Redding bushing come with a die or shellholder?
No, this is just the bushing itself, sold as a single unit. Dies and shellholders are purchased separately. Many reloaders buy a bushing a thousandth above and below their target so they can fine-tune neck tension when working up a load.



Reviews
There are no reviews yet.