Description
The Redding Competition Bushing Neck Die for 6.5 Creedmoor is built for reloaders who sweat the small stuff. It works a lot like Redding's Competition Seating Die, where the case is fully supported and aligned with the sizing bushing before any sizing even starts. As the ram comes up, the case stays cradled in a tightly chambered sliding sleeve while the bushing self-centers on the neck. That support is what keeps runout low and neck tension consistent from one case to the next, which is exactly what you want when you're trying to shrink groups.
How the 6.5 Creedmoor Competition Neck Die Works
This die uses interchangeable sizing bushings that step in .001 inch increments, so you can tune neck tension precisely to your brass and your bullet. The micrometer adjustment on the bushing position lets you size the full neck or just part of it, which is handy for folks who like partial neck sizing. The decapping rod rides in precise alignment thanks to the internal parts acting as linear support, similar to how a firing pin is guided, so your depriming stays true and your necks stay straight.
Who the Competition Bushing Neck Die Is Built For
Redding designed this one for the handloader who preps brass with intent. It's aimed at people who sort their cases for neck wall thickness or turn their necks for uniformity and don't want a sizing button dragging through the neck. If that's your workflow, the bushing does the work and you keep tighter control. If you prefer running an expander, Redding offers carbide size button kits separately.
What to Know Before You Order
A couple of things to plan for. Neck sizing bushings are sold separately so you can match the exact size to your brass, and the shellholder isn't included either. 6.5 Creedmoor uses a #1 shellholder, with a bullet diameter of .264 and a bushing range that runs roughly .285 to .293. Pick your bushing by measuring a loaded round and subtracting a thousandth or two for proper bullet grip.
Key Specifications
- Manufacturer: Redding
- Manufacturer Part Number: 56446
- UPC: 611760564468
- Caliber: 6.5mm Creedmoor
- Die Type: Competition Bushing Neck Sizing Die
- Bullet Diameter: .264 in
- Bushing Range: .285 to .293 in
- Bushing Increments: .001 in interchangeable bushings
- Adjustment: Micrometer bushing position adjustment
- Shellholder: #1 (sold separately)
- Thread: 7/8-14
- Country of Origin: United States
What’s Included
- Competition Bushing Neck Sizing Die (one die)
- Decapping rod assembly
Frequently Asked Questions
Does the Competition Bushing Neck Die come with bushings?
No, neck sizing bushings are sold separately so you can match the exact bushing to your brass and your desired neck tension. 6.5 Creedmoor typically falls in the .285 to .293 range. The easiest way to size is to measure the neck of a loaded round and subtract .001 to .002 inches.
Is a size button included with this die?
This die does not include a sizing button, which is by design. Redding built it for reloaders who sort brass for neck wall thickness or turn their necks, letting the bushing control neck sizing without an expander dragging through. If you want to run a button, Redding offers carbide size button kits separately.
Do I need a shellholder for the 6.5 Creedmoor Competition Neck Die?
Yes, and it is not included in the box. The 6.5 Creedmoor uses a standard #1 shellholder. If you already reload this cartridge there's a good chance you have the right one on hand.
What makes the Competition Bushing Neck Die different from a standard neck die?
The case is fully supported and aligned inside a close-fitting sliding sleeve before sizing begins, and the bushing self-centers on the neck. That extra support reduces neck runout and gives you more consistent neck tension round to round. The micrometer also lets you adjust how much of the neck length gets sized.





Reviews
There are no reviews yet.