Description
The 270 Winchester has been putting elk and deer on the ground for a century, and if you reload for one, this Redding Type S-Match set is about as good as it gets short of custom dies. It pairs a Type S bushing full-length sizing die with Redding's Competition Seating Die, giving you real control over the two things that matter most for accuracy: neck tension and seating depth. This is the die set competitive shooters lean on when they want precise, repeatable ammo that still chambers and feeds without a fuss.
What Sets the Type S-Match Bushing Die Apart
The magic here is the interchangeable bushing system. The full-length sizing die uses drop-in bushings available in .001-inch increments, so you choose exactly how much you want to work the neck and what neck tension you're after. That means less overworking of your brass, which stretches case life and keeps your necks more uniform load after load. The die sizes the case body and bumps the shoulder in the same stroke, and the bushings self-center to help keep runout to a minimum. Pull the bushing and the internals and it doubles as a body die if you want to go that route.
Fine-Tuning With the Competition Seating Die
The seating die is where this set really earns its keep. A sliding sleeve captures and aligns the case before the bullet ever touches the seating stem, which goes a long way toward straight, concentric ammo. On top sits a micrometer head that lets you adjust seating depth in .001-inch clicks and dial right back to a setting you've logged before. If you're chasing the ideal bullet jump for a particular load, that repeatability saves a ton of guesswork at the bench.
Built to Last
Redding has been building reloading gear in the USA since 1946, and the machining and heat treating on these dies holds up for the long haul. Keep in mind the sizing bushings and shellholder are sold separately, so you'll want to grab the right bushing for your brass and neck tension goals before your first session. The Competition Seating Die ships with a standard seating stem that handles most bullet shapes, with VLD stems offered separately if you're running long, pointy match bullets.
Key Specifications
- Manufacturer: Redding
- Manufacturer Part Number: 36135
- UPC: 611760361357
- Cartridge: .270 Winchester
- Die Set Type: Type S-Match Bushing Full Length (2-Die)
- Sizing Die: Type S Bushing Full Length Sizing Die
- Seating Die: Competition Seating Die with micrometer head and sliding sleeve
- Neck Sizing Adjustment: Interchangeable bushings in .001" increments
- Seating Adjustment: Micrometer, .001" increments
- Material: Case hardened steel
- Thread Size: 7/8"-14
- Country of Origin: USA
What’s Included
- Type S Bushing Full Length Sizing Die with decapping rod, standard sizing button, and decapping pin retainer
- Competition Bullet Seating Die with sliding sleeve and micrometer adjusting head
- Plastic storage box
- Complete instructions
Frequently Asked Questions
Are bushings included with this 270 Winchester Type S-Match die set?
No, the sizing bushings are sold separately. This lets you pick the exact bushing size for your brass and the neck tension you want, since Redding offers them in .001-inch increments. Measure a loaded round's neck diameter and subtract a couple thousandths to figure out where to start.
Does this set come with a shellholder?
It does not. The shellholder is sold separately, so you'll want to grab the correct one for the 270 Winchester case head before you start resizing.
What makes the Competition Seating Die better than a standard seater?
The Competition Seating Die uses a sliding sleeve that fully captures and aligns the case before the bullet contacts the stem, which produces very straight, concentric ammo. It also has a micrometer head so you can adjust seating depth in .001-inch increments and return to a recorded setting easily. That repeatability is a big help during load development.
Can the sizing die be used as a body die?
Yes. Remove the bushing and the internal parts and the Type S full-length sizing die works as a body die, sizing the case body and bumping the shoulder without touching the neck. It's a handy bit of flexibility if your reloading process ever calls for it.





Reviews
There are no reviews yet.