Description
A good crimp is one of those details that separates ammo that groups well from ammo that just goes bang, especially on heavy-recoiling revolver loads where bullet pull matters. Redding's Micrometer Adjustable Profile Crimp Die for 38 Special and 357 Magnum takes the guesswork out of that step. Instead of the usual loosen-the-lock-ring, guess, and re-check routine, you get a knurled micrometer head up top that lets you fine-tune crimp depth right on the press.
What the Micrometer Head on This Profile Crimp Die Gets You
The adjustment barrel sits on top of the die and delivers roughly plus or minus .100 inch of travel in .001-inch increments. That means you can nudge the crimp tighter or back it off a hair without pulling the die or resetting anything. Case length and neck wall thickness both affect where the brass meets the crimping surface, and the fine-thread micrometer makes it easy to compensate for that variation and keep every round consistent.
One Die, Both 38 Special and 357 Magnum
The internal crimping sleeve is reversible, so one die covers both cartridges. Flip the sleeve to match the case you are loading and you are set, no need to buy a separate die for each round. The profile crimp itself forms a cleaner, more uniform roll-type crimp than a standard roll die, which helps with bullet retention and shot-to-shot uniformity. Keep in mind the bullet needs to be seated to final depth in a previous step, since this is a dedicated crimping die and not a seat-and-crimp combo.
Built the Redding Way
Redding has been machining reloading gear in New York since the 1940s, and this die carries that reputation. The body is cut to tight tolerances for a close-fitting lead-in, which helps keep the finished round concentric. Handloaders who run progressive presses tend to appreciate how the top-adjusting design works in tight spaces and keeps production moving without constant readjustment.
Key Specifications
- Manufacturer: Redding
- Manufacturer Part Number: 31282
- UPC: 611760312823
- Die Type: Micrometer Adjustable Profile Crimp
- Cartridge: 38 Special / 357 Magnum
- Crimp Style: Profile (roll-type)
- Adjustment: Top-adjusting micrometer head, .001-inch increments
- Adjustment Range: Approximately plus or minus .100 inch
- Crimping Sleeve: Reversible to cover both cartridges
- Thread: 7/8-14
- Country of Origin: USA
What’s Included
- Redding Micrometer Adjustable Profile Crimp Die (38 Special / 357 Magnum)
- Lock ring
- Instructions
Frequently Asked Questions
Does this profile crimp die seat the bullet too, or just crimp?
It is a dedicated crimping die, so it only applies the crimp. Your bullet needs to be seated to its final depth in a separate operation before this step. Keeping seating and crimping as two stages generally gives you cleaner, more consistent results.
Can one die handle both 38 Special and 357 Magnum?
Yes. The internal crimping sleeve is reversible, so you flip it to match whichever cartridge you are loading. That lets a single die cover both rounds without buying a second one.
What makes the micrometer adjustment better than a standard crimp die?
The micrometer head sits on top of the die and lets you fine-tune crimp depth in .001-inch increments without loosening the lock ring or pulling the die. Traditional crimp dies require guessing and re-checking after each turn. This top-adjusting design makes it easy to dial in repeatable crimps and works well on progressive presses with limited clearance.
What is a profile crimp compared to a roll or taper crimp?
A profile crimp forms a tighter, more uniform roll-type crimp that curls the case mouth into the bullet's crimp groove for strong bullet retention. It is well suited to revolver rounds like 38 Special and 357 Magnum where recoil can pull bullets loose. It is not intended for cartridges that headspace on the case mouth.





Reviews
There are no reviews yet.