Description
This is MEC's Progressive Stage Lead Skeet Special charge bar set up to drop 1-1/8 ounces of lead shot in 12 gauge. The 502 series designation means it fits every MEC progressive press, so whether you're running a 650, a Grabber, or a 9000-series machine, this bar drops right into your setup and gets you back to loading. The charge bar controls how much shot gets dropped, while a removable powder bushing (sold separately) handles the powder side of your recipe.
Machined from anodized aluminum, this bar is built to hold its dimensions through load after load. One of the nicer touches on the 502 series is the soft insert, which helps prevent shearing when you're working with larger or harder lead shot. That insert also means you can skip the grommet under the shot bottle that older setups required, which is one less thing to fuss with on your press.
What Makes the Skeet Special Charge Bar Different
The "Skeet Special" part is the whole point here. When you run soft #9 shot through a standard bar, the charge can come out heavier than skeet competitors want. This bar is cut specifically to meter soft #9 skeet loads to the right weight, which is why dedicated skeet reloaders reach for it instead of a general-purpose bar. If #9 is your bread and butter on the skeet field, this is the bar that keeps your loads where you want them.
Getting the Most From Your 502118SS Charge Bar
A quick note worth knowing: this bar is tuned around soft, non-magnum #9 shot. If you switch to magnum or hard shot, or go up in shot size, expect the drop weight to change, so it's always smart to weigh a few charges when you set up a new load. Pair it with the correct MEC powder bushing from the selection chart for your powder and recipe, and you'll have a repeatable, competition-ready setup for your progressive press.
Key Specifications
- Manufacturer: MEC (Mayville Engineering Company)
- Manufacturer Part Number: 502118SS
- UPC: 098489015790
- Type: Progressive Stage Lead Skeet Special Charge Bar
- Shot Weight: 1-1/8 oz
- Gauge: 12 Gauge
- Shot Type: Lead (not interchangeable with steel bars)
- Series: 502 (Progressive)
- Material: Anodized Aluminum
- Press Compatibility: All MEC progressive presses (650, Grabber, 9000)
- Soft Insert: Yes, replacement Part #8440
- Powder Bushing: Accepts removable bushings (sold separately)
What’s Included
- One MEC 502118SS Progressive Stage Lead Skeet Special charge bar (1-1/8 oz, 12 gauge)
Frequently Asked Questions
Which MEC presses does the 502118SS charge bar fit?
The 502 series designation means this bar works in all MEC progressive presses, including the 650, Grabber, and 9000-series machines. The 302 series is the single-stage equivalent, so make sure you're matching the series to your press. If you have a progressive setup, this bar drops right in.
Does this charge bar come with a powder bushing?
No, the powder bushing is sold separately. The charge bar meters your shot drop, while the removable bushing controls the powder charge. Check MEC's bushing selection chart to pick the right bushing for your specific powder and recipe.
What makes the Skeet Special bar different from a standard MEC bar?
A standard bar can throw a heavier-than-intended charge when loading soft #9 shot, which matters to skeet competitors. The Skeet Special bar is cut to meter soft #9 skeet loads to the correct weight. It's the bar of choice if #9 is your go-to skeet load.
Will this bar drop an accurate charge with magnum or larger shot?
This bar is tuned around soft, non-magnum #9 shot, so switching to magnum shot or going up in shot size will typically change the drop weight, usually throwing lighter. Whenever you set up a new load, it's a good habit to weigh a few charges to confirm your drop. For soft #9 skeet loads, it's right at home.




Reviews
There are no reviews yet.