0
0

.262″ Hornady Match Grade Bushing 6mm – Neck Sizing Die Bushing

UPC: 090255592627

$23.99

1 in stock

Online inventory may differ from in-store availability. 

Fast Shipping

Quick turnaround so you get your gear sooner.

Secure FFL-Friendly Checkout

Trusted checkout with industry-standard protection.

Family-Owned Business

Keeping Traditions Alive Since 1953

Secure Transactions provided with

Description

This is the .262" diameter neck sizing bushing from Hornady's Match Grade system, built for 6mm cartridges like the 6mm PPC and .243 Winchester family. Rather than sizing your case necks down to a one-size-fits-all SAAMI minimum, this bushing lets you size only as much as you need to hit the exact neck tension your loads call for. That kind of control is where consistent groups start, and it's the main reason handloaders chasing precision reach for the bushing system.

How the .262" 6mm Bushing Works

The bushing drops into both the Match Grade full length die and the Match Grade neck sizing die. In the full length die it sizes the case body, bumps the shoulder, and sizes the neck with the bushing you've chosen. In the neck die it bumps the shoulder and sizes the neck only, leaving the body alone. It's self-centering inside the die body, so it floats into alignment with the case neck instead of fighting it, which keeps runout down and your necks concentric.

Picking the Right Match Grade Bushing Size

Hornady offers these bushings in .002" increments so you can fine-tune neck tension across your brass. A reliable starting point is to measure the neck diameter of a loaded round that chambers well, then subtract about .001" and choose a bushing at or just under that number. The .262" size sits right in the useful range for 6mm PPC and .243 Winchester shooters, and because bushings are interchangeable, you can keep a few on hand and adjust tension as your brass springs back differently through its life.

What Makes This Bushing Worth It

For anyone already running Hornady Match Grade dies, adding bushings is the easy upgrade that turns a good die set into a true precision setup. Less sizing means less overworking the brass, which stretches case life and keeps your loads uniform from the first firing to the last. Keep in mind the bushing is not included with the dies, so you'll want the correct diameter to match your chamber and brass.

Key Specifications

  • Manufacturer: Hornady
  • Manufacturer Part Number: 594262
  • UPC: 090255592627
  • Bushing Inside Diameter: .262 inch
  • Caliber: 6mm (6mm PPC, .243 Winchester)
  • Outside Diameter: .750 inch
  • Tolerance: Within .002 inch
  • Material: Polished Steel
  • Design: Self-centering, interchangeable
  • Compatibility: Hornady Match Grade full length and neck sizing dies
  • Available Increments: .002 inch
  • Quantity: 1 bushing
  • Country of Origin: United States

What’s Included

  • One .262" Hornady Match Grade neck sizing bushing

Frequently Asked Questions

What dies does the .262" Hornady Match Grade bushing fit?

It fits both the Hornady Match Grade full length sizing die and the Match Grade neck sizing die. In the full length die it sizes the body, bumps the shoulder, and sizes the neck. In the neck die it bumps the shoulder and sizes only the neck. The bushing is not included with the dies, so you buy the diameter you need separately.

What cartridges is the .262 6mm bushing meant for?

This .262" size is built for 6mm cartridges, and it falls in the common range used by 6mm PPC and .243 Winchester handloaders. Because the system runs in .002" steps, many precision shooters keep a few neighboring sizes on hand to tune neck tension to their specific brass and chamber.

How do I know if .262" is the right bushing size for my loads?

Measure the neck diameter of a loaded round that chambers cleanly in your rifle, then subtract about .001" and pick the bushing at or just under that number. That gives you a solid starting point for neck tension. From there you can step up or down in .002" increments to fine-tune your loads.

Why use a bushing instead of a standard sizing die?

A standard die sizes necks down to SAAMI minimum, which often works the brass more than it needs to. A bushing lets you size only as much as required for the tension you want, so the brass flexes less and lasts longer. The self-centering design also helps keep necks concentric, which supports tighter groups.

Additional information

UPC

090255592627

Manufacturer

Manufacturer Part Number

594262

Reviews

There are no reviews yet.

Be the first to review “.262″ Hornady Match Grade Bushing 6mm – Neck Sizing Die Bushing”