Description
Devcon Plastic Steel Liquid (B) is a two-part, steel-filled epoxy that pours like thick honey and cures into a tough, dense mass you can drill, tap, and machine. It's a shop staple that's been around for decades, and while the industrial world uses it for holding fixtures, forming dies, and leveling machinery, gunsmiths have leaned on it for years for one big reason: it's loaded with real steel and it doesn't shrink as it cures. That combination makes it a favorite for bedding rifle actions and repairing worn or stripped bolt holes.
Why Gunsmiths Trust the Plastic Steel Liquid Formula
The steel filler is the whole story here. It gives the cured epoxy serious compressive strength, around 10,200 psi, along with a hardness of about 85 Shore D. When you bed an action with it, you get a rock-solid, stable platform that won't pull away from the metal as it sets. Folks also use it to fill and re-tap broken or stripped screw holes, then run the bolt right back in once it's cured. Anywhere you'd think about pulling out a welder but can't, this stuff steps in.
Working Time and Cure on the Devcon 10210
You get roughly a 45-minute working window, so there's no need to rush your mix or your layup. It hardens in about an hour and reaches full cure in around 16 hours at 75 degrees F. For best results, let it cure at least 12 hours before you start machining. A quick tip from the trenches: use a good release agent on any metal you don't want it bonding to permanently, because once this cures onto bare steel, it means business.
Getting Clean Results
The low viscosity is what lets it flow into fine detail and tight cavities, which is exactly why it reproduces model detail so well and settles into bedding channels cleanly. Pour it in a thin stream, no thicker than an inch at a time, to chase out trapped air. Once it kicks, you've got a dark grey, machinable surface that resists a range of chemicals and handles operating temps up to 250 degrees F.
Key Specifications
- Manufacturer: Devcon
- Manufacturer Part Number: 230-10210
- Model: 10210
- UPC: 078143102103
- Product Type: Steel-Filled Liquid Epoxy
- Net Weight: 1 lb
- Color: Dark Grey
- Working Time: 45 minutes
- Full Cure Time: 16 hours at 75°F
- Compressive Strength: 10,200 psi
- Tensile Shear Strength: 2,800 psi
- Hardness: 85 Shore D
- Viscosity: 20,000 cP
- Max Operating Temperature: 250°F
- Chemical Compound: Two-Part Epoxy
What’s Included
- 1 lb kit Devcon Plastic Steel Liquid (B) epoxy resin
- Hardener
Frequently Asked Questions
Can I use Devcon Plastic Steel Liquid (B) to bed a rifle action?
Yes, it's a well-known choice for action bedding because it's steel-filled and doesn't shrink as it cures, so it stays tight against the metal. The dense, high-compression cure gives your action a stable, solid platform. Just be sure to coat the barreled action with a quality release agent first, since this epoxy bonds aggressively to bare metal.
How long does the Devcon 10210 take to set and cure?
You've got about a 45-minute working window to mix and apply it. It hardens in roughly an hour and reaches full cure in about 16 hours at 75 degrees F. Let it cure at least 12 hours before drilling, tapping, or machining for the cleanest results.
Can the Plastic Steel Liquid epoxy be drilled and tapped after it cures?
It can. Once fully cured it machines to close tolerances and can be drilled, tapped, and even painted. That's why it works so well for repairing stripped or broken screw holes, where you fill the hole, cut new threads, and run the bolt back in.
What's the difference between Plastic Steel Liquid and the putty version?
The liquid pours and self-levels thanks to its low viscosity, so it flows into fine detail and tight cavities, which makes it ideal for casting, bedding, and leveling work. The putty is a thicker, hand-packable compound better suited for building up shapes and patching vertical surfaces. Both are steel-filled and machinable once cured, so the right pick just depends on whether you need it to flow or stay put.



Reviews
There are no reviews yet.