Description
The L.E. Wilson 338 Lapua Micrometer Top Bullet Seater is a chamber-type hand die built for reloaders who care about concentricity and consistency with the big .338 Lapua Magnum. Instead of threading into a conventional press, the case and bullet are fully captured inside the die body and the bullet is pushed straight down into the neck by a close-fitting seating stem. That design keeps everything in alignment and is a big reason these dies are a longtime favorite on the benchrest and long-range crowd.
What Sets the Wilson 338 Lapua Micrometer Seater Apart
The micrometer top is the headline feature here. It reads in .001-inch graduations, so adjusting seating depth is quick, repeatable, and easy to return to a known setting. A lot of folks set the micrometer so a reference point lines up with where the bullet touches the lands, which makes jumping back and forth between seating depths during load development painless. Larger adjustments can be made through the 3/8-24 TPI threads in the cap.
Running the 338 Lapua Micrometer Top Seater
This is a hand die, meaning it runs with an arbor press or, in a pinch, a soft-faced mallet. It is not made for a threaded press. The workflow is simple: set a bullet on a charged and primed case, drop both into the die body, place it on the base, and press the cap down until it bottoms out. Reloaders like that it gives you a real feel for seating force, so you can set aside any round that seats noticeably hard or light. For the smoothest results, a quality arbor press like the K&M pairs naturally with this die.
Built to Last
Made in the USA from stainless steel and machined to tight tolerances, this seater is the kind of tool you buy once. L.E. Wilson has been turning out precision reloading gear since 1927, and the fit and finish reflect that long track record. If you are loading precision .338 Lapua Magnum ammo and want to shrink runout and keep your seating depth dead consistent, this die earns its spot on the bench.
Key Specifications
- Caliber: 338 Lapua Magnum
- Die Type: Chamber-Type Micrometer Top Bullet Seater
- Micrometer Graduations: .001-inch increments
- Cap Thread: 3/8-24 TPI
- Material: Stainless Steel
- Press Compatibility: Arbor press or soft-faced mallet (not for conventional threaded presses)
- Manufacturer: L.E. Wilson
- Manufacturer Part Number: S33-8LP
- UPC: 815145022608
- Country of Origin: Made in the USA
- Shipping Weight: 1.03 lbs
What’s Included
- L.E. Wilson 338 Lapua Micrometer Top Bullet Seater die body
- Base
- Seater cap with seating stem
Frequently Asked Questions
Does the 338 Lapua Micrometer Top Bullet Seater work in a standard reloading press?
No, this is a hand die designed for use with an arbor press or a soft-faced mallet. It is not made to thread into a conventional press. Most reloaders pair it with a small arbor press for the smoothest, most consistent results.
What does the micrometer top actually do?
The micrometer lets you adjust seating depth in precise .001-inch increments and return to a known setting with ease. Many reloaders zero it to where the bullet touches the lands, which makes load development and bouncing between seating depths quick and repeatable. Larger adjustments are handled through the 3/8-24 TPI threads in the cap.
Why choose a Wilson chamber-type seater over a conventional seating die?
A chamber-type seater fully captures both the case and bullet before the bullet is pushed straight into the neck, which keeps everything in tight alignment. That translates to lower bullet runout and better concentricity, which is why these are a favorite among benchrest and long-range precision reloaders.
Will this die seat VLD and long-range bullets in .338 Lapua?
Yes, the included seating stem handles a wide range of .338 Lapua Magnum bullets, including long VLD-style projectiles. If you run an unusual bullet profile, Wilson and other vendors also offer seating stems and die blanks for custom fitting.



Reviews
There are no reviews yet.