Description
Part of Rob Roberts' Raptor lineup (sold here under the Johnny Stewart name), the RR2 is the mid-range tube in a three-choke system. Where the RR1 handles close work and the RR3 reaches out for geese and open-water ducks, the RR2 sits right in the sweet spot for the shots most wingshooters take. Think decoying mallards, doves crossing a sunflower field, and flooded timber where birds fold in at moderate distances. The internal cuts machined into the tube tighten up the core of your pattern, so when you pair it with the right load you get a denser, more consistent hit downrange.
What Sets the RR2 Raptor Apart
This choke is built from 17-4 PH U.S. stainless steel and heat treated, which is what gives it the corrosion resistance and durability you want in a tube that lives in a wet duck blind or a dusty dove field. The Raptor series was designed with the same thinking behind Rob Roberts' well-known Triple Threat chokes, but with newer technology aimed at throwing a hotter core pattern. Folks who have patterned these tubes consistently report tight, even patterns across a range of loads, and they play nice with lead, steel, and other non-toxic shot.
Fitment for Your Optima HP Shotgun
This particular tube is cut for the Beretta Optima HP thread pattern, which covers popular guns like the A400 and the 1301 in 20 gauge. Instead of the traditional knurled band, the Raptor tubes wear machined claw marks and a Cerakote finish on the extended portion, so they look as sharp as they shoot. One thing worth knowing if you run an over/under: the Raptor design is meant to go in only one barrel, not both.
If you have been running a factory tube and want more reach and density without jumping all the way to a long-range constriction, the RR2 is the practical middle ground. It is a purpose-built hunting choke that rewards you with cleaner kills at the distances birds actually show up.
Key Specifications
- Manufacturer: Johnny Stewart (Rob Roberts Gun Works)
- Model: RR2 Raptor
- Manufacturer Part Number: 200320
- UPC: 810174902297
- Caliber/Gauge: 20 Gauge
- Choke Type: Mid-Range (RR2)
- Thread Pattern: Beretta Optima HP (A400, 1301)
- Material: 17-4 PH U.S. Stainless Steel
- Shot Compatibility: Lead, Steel, and Non-Toxic
- Intended Use: Duck and Dove Hunting
- Finish: Cerakote on extended portion, machined claw marks
What’s Included
- RR2 Raptor Optima HP 20 Gauge Choke Tube
Frequently Asked Questions
What shotguns does the RR2 Raptor Optima HP choke fit?
This tube is threaded for the Beretta Optima HP system, which covers popular 20 gauge guns like the Beretta A400 and the 1301. If your barrel is marked Optima HP, this is the pattern you want. When in doubt, check your barrel markings or your owner's manual to confirm the thread before ordering.
What is the difference between the RR1, RR2, and RR3 Raptor chokes?
The RR1 is tuned for close-range work, the RR2 is the mid-range choke aimed at duck and dove hunting, and the RR3 reaches out for long-range birds like geese and open-water ducks. This listing is the RR2, so it sits in the middle for the distances most wingshooters actually take their shots. All three use internal cuts to tighten the core of the pattern.
Can I use steel and non-toxic shot with the RR2 Raptor?
Yes. The choke is made from heat-treated 17-4 PH U.S. stainless steel, so it handles lead, steel, and other non-toxic loads just fine. As always, pattern your specific load through the tube to see what it likes best before opening day.
Can I run two Raptor chokes in an over/under?
No. The Raptor design is meant to be installed in only one barrel of an over/under, not both. If you shoot an O/U, plan to run the RR2 in a single barrel and pair it with something else in the other.




Reviews
There are no reviews yet.