Description
If you're loading 6.5×47 Lapua for precision work, the Forster Bushing Bump Kit takes a lot of the guesswork out of neck sizing. Instead of running cases through a conventional neck die and hoping for the best, this setup lets you pick the exact amount of bullet grip you want by swapping bushings. In one stroke it sizes the neck to your chosen bushing, bumps the shoulder back just enough for smooth chambering, and deprimes the case. That combination is a big reason the 6.5×47 Lapua has earned its reputation as a benchrest and long-range favorite, and this kit plays right into that strength.
What the 6.5×47 Lapua Bushing Bump Kit Brings to Your Bench
The real advantage here is control. Because you're only sizing the neck down as much as necessary while nudging the shoulder, the brass body keeps its fire-formed dimensions. That means less work hardening, longer case life, and the kind of shot-to-shot consistency that shows up on paper. You get the option to run the included expander ball or pull it out entirely if your necks are turned to a uniform wall thickness, which gives you a couple of ways to approach the job depending on your brass prep.
Bushings, Fit, and Setup
The kit ships with three Forster bushings pre-selected for the cartridge in .287, .289, and .291 diameters, which cover most common brass and neck tension needs right out of the gate. Forster offers interchangeable bushings in .001 inch increments if you need to fine-tune further, and keep in mind these dies only accept Forster-made bushings. The die uses a standard 7/8-14 thread, so it threads into any common single-stage press. Interior surfaces are hand polished for smooth sizing, and the whole thing is machined and heat treated in the USA to the tight tolerances Forster is known for.
For a cartridge built around precision like the 6.5×47 Lapua, this kit is a smart way to stretch your brass and tighten your groups without overcomplicating your reloading routine.
Key Specifications
- Manufacturer: Forster Products
- Cartridge: 6.5×47 Lapua
- Die Type: Bushing Bump Neck Sizing Die
- Included Bushing Sizes: .287, .289, .291 diameter
- Thread: 7/8-14 standard
- Material: Hardened steel, hand polished interior
- Bushing Compatibility: Forster bushings only, available in .001 inch increments
- Country of Origin: USA
- Manufacturer Part Number: BBK2261
- UPC: 757253996375
- Shipping Weight: 0.575 lb
What’s Included
- One Forster Bushing Bump Neck Sizing Die
- Three neck sizing bushings pre-selected by Forster (.287, .289, .291)
- Decapping assembly
- Complete instructions
Frequently Asked Questions
What bushings come with the Forster Bushing Bump Kit for 6.5×47 Lapua?
The kit includes three Forster bushings in .287, .289, and .291 diameters. These are pre-selected to cover most common brass and neck tension needs for the 6.5×47 Lapua. If you need a different amount of sizing, Forster makes interchangeable bushings in .001 inch increments, and the die only accepts Forster-made bushings.
Does this die bump the shoulder and size the neck at the same time?
Yes. The bushing bump design sizes the case neck to your chosen bushing while bumping the shoulder back slightly in a single operation. That keeps your case necks straighter and maintains proper headspace for smooth chambering, all without overworking the brass body.
Will the Forster Bushing Bump Kit work in my press?
It uses a standard 7/8-14 thread, so it threads into any common single-stage reloading press. If you're running a Forster Co-Ax press, you won't need a separate shellholder since those presses don't require one.
Can I remove the expander ball?
You can run it either way. If your brass is neck turned to a uniform wall thickness, you can remove the expander ball and let the bushing do all the outside sizing. If your necks aren't turned, leaving the expander ball in helps keep inside neck diameter consistent for more uniform bullet grip.




Reviews
There are no reviews yet.