Description
Neck tension is one of those things that quietly separates good handloads from great ones, and the Forster 308 Neck Tension Gage gives you a simple way to measure it. After you've neck sized your .30 caliber brass and before you seat bullets, this tool reads the inside diameter of your case necks so you can confirm you're getting a consistent grip on the bullet round after round. It's a small piece of machined steel, but it takes a lot of the guesswork out of case prep.
How the Forster NTG-308 Works
The gage uses four stepped diameters that grow in size as they move toward the handle, and each step is etched right into the metal so there's no squinting or cross-referencing. You slide the stepped end into a sized case neck until one of the diameters reaches a slip fit. On the .308 version those four steps measure 0.3040, 0.3050, 0.3060, and 0.3070 inches, held to a tight tolerance, which covers the common bushing and mandrel setups people run for .30 caliber. Your actual inside neck diameter falls between the last step the neck slid over and the one it stopped against.
Putting the 308 Neck Tension Gage to Work
Beyond setting tension, this is a handy inspection tool. Running it into your necks will tell you if a donut has started forming at the neck-shoulder junction, which is the kind of thing that can throw off seating and accuracy without you realizing it. Once you've read a few cases, you can go back and fine-tune your sizing, whether that means swapping a bushing, adjusting a mandrel, or changing up your case conditioning routine.
For anyone chasing tighter groups with a bolt gun or sorting brass for match loads, having real numbers instead of feel makes a difference. It's quick enough to screen a whole batch in a sitting and fits right in with the rest of your reloading bench tools. Forster backs it with a lifetime warranty against defects in materials and workmanship, which is about what you'd expect from their precision gear.
Key Specifications
- Manufacturer: Forster Products
- Model: NTG-308
- Manufacturer Part Number: NTG-308
- UPC: 757253991110
- Caliber: .30 Caliber / 7.62mm (.308")
- Tool Type: Neck Tension / Inside Neck Diameter Inspection Gage
- Stepped Diameters: 0.3040", 0.3050", 0.3060", 0.3070"
- Number of Steps: 4
- Diameter Tolerance: ±0.00015"
- Markings: Each diameter etched on the tool
- Shipping Weight: 0.105 lbs
- Warranty: Lifetime against defects in materials and workmanship
What’s Included
- Forster NTG-308 Neck Tension Gage (30 Caliber / .308)
Frequently Asked Questions
What diameters does the Forster 308 Neck Tension Gage measure?
The NTG-308 has four stepped diameters etched into the tool: 0.3040, 0.3050, 0.3060, and 0.3070 inches. Each step is held to a tolerance of roughly ±0.00015 inch. You read your inside neck diameter by noting the last step your neck slides over and the one it stops against.
When should I use the 308 Neck Tension Gage during reloading?
Use it after neck sizing your brass and before seating bullets. That's the window where measuring inside neck diameter tells you how much tension you'll have on the bullet. It's a quick way to screen and sort a batch so your seating stays consistent.
Can the Forster NTG-308 detect a donut in the case neck?
Yes. Running the gage into your sized necks will reveal if a donut has started forming at the neck-shoulder junction, since that buildup changes the inside diameter. Catching it early helps you keep seating smooth and avoid the accuracy issues a donut can cause.
Will this gage work for all .30 caliber cartridges?
It's built for .30 caliber (.308 bullet) brass, so it works across cartridges that use that bullet diameter like .308 Winchester, .30-06, .300 Win Mag, and similar. It reads the inside of the sized neck, not the cartridge itself, so any .30 cal case you've neck sized can be checked with it.




Reviews
There are no reviews yet.