0
0

Forster 6.5 Creedmoor Bushing Full-Length Die Kit w/ 3 Bushings

UPC: 757253990595

$134.99

1 in stock

Online inventory may differ from in-store availability. 

Fast Shipping

Quick turnaround so you get your gear sooner.

Secure FFL-Friendly Checkout

Trusted checkout with industry-standard protection.

Family-Owned Business

Keeping Traditions Alive Since 1953

Secure Transactions provided with

Description

Forster's Bushing Full-Length Die Kit for 6.5 Creedmoor gives you the best of both worlds: it sizes the case body and bumps the shoulder like a standard full-length die, but it also lets you control neck tension through interchangeable bushings. The body and shoulder get sized down just enough to fit a minimum-spec SAAMI chamber, while the bushing handles the neck separately. That means your brass isn't getting over-squeezed on every cycle, which is exactly what you want if you reload the same cases season after season.

What Sets This 6.5 Creedmoor Bushing Die Apart

The die body is hand-polished with a smooth machined interior, so cases feed in and out cleanly with proper lube. Where this kit earns its keep is the bushing system. The neck only gets reduced as much as the bushing allows, so you grip the bullet reliably without working the brass harder than necessary. Less work means fewer annealing cycles and more loadings before necks start to split. A general starting point is to pick a bushing roughly .002 inch under the neck diameter of a loaded round, which lands you right around the common .002 inch neck tension most loaders are after.

Dialing In Neck Tension With the Forster Die Kit

The kit ships with three bushings in .288, .290, and .292, covering the typical range of 6.5 Creedmoor neck wall thicknesses. Forster also offers bushings in .001 inch increments if you need to fine-tune further or you're running turned necks. The die includes a high-mounted floating expander and decapping assembly, which helps keep runout low by centering the neck before the expander enters. If you're turning your necks to a uniform wall thickness, the expander ball can be pulled so the bushing alone sets your tension.

This is a sizing die kit, so you'll still want a quality seater to finish your loads. It's a solid pick for precision rifle shooters, hunters loading for consistency, and anyone chasing tighter ES and SD numbers out of their 6.5 Creedmoor.

Key Specifications

  • Manufacturer: Forster Products
  • Cartridge: 6.5mm Creedmoor
  • Die Type: Bushing Full-Length Sizing Die
  • Bushings Included: Three (.288, .290, .292)
  • Bushing Increments Available: .001 inch
  • Expander: High-mounted floating expander, removable
  • Decapping: Includes decapping assembly
  • Manufacturer Part Number: FBK4271
  • UPC: 757253990595
  • Shipping Weight: 0.575 lb

What’s Included

  • One Forster Bushing Full-Length Sizing Die for 6.5 Creedmoor
  • Three neck bushings pre-selected by Forster (.288, .290, .292)
  • Decapping and expander assembly
  • User instructions

Frequently Asked Questions

What bushings come with the Forster 6.5 Creedmoor die kit?

The kit includes three bushings in .288, .290, and .292, pre-selected by Forster to cover most 6.5 Creedmoor brass. If you need a different size for turned necks or a specific neck tension, Forster offers bushings in .001 inch increments sold separately. A good starting point is a bushing about .002 inch smaller than the neck diameter of a loaded round.

Does this die full-length size or just size the neck?

It does both. The die sizes the case body and bumps the shoulder to fit a minimum-spec SAAMI chamber, while the bushing handles the neck separately. That combination gives you reliable chambering along with the control over neck tension that a dedicated bushing die provides.

Can I remove the expander ball on this Forster bushing die?

Yes. The decapping and expander assembly is removable, which is handy if you turn your necks to a uniform wall thickness and want the bushing alone to set your neck tension. Many loaders keep the floating expander in place, though, since it helps center the neck and keep runout low.

Do I need anything else to load with this kit?

This is a sizing die kit, so you'll still need a seating die to finish your rounds. You'll also want case lube, since full-length sizing works best with a lightly lubricated case body and shoulder. A trimmer and chamfer tool round out a proper precision reloading setup.

Additional information

UPC

757253990595

Manufacturer

Manufacturer Part Number

FBK4271

Shipping Weight

0.575

Reviews

There are no reviews yet.

Be the first to review “Forster 6.5 Creedmoor Bushing Full-Length Die Kit w/ 3 Bushings”