0
0

Forster 6.5 PRC Bushing Full Length Die Set, 2-Die w/ Bushings

UPC: 757253990465

$230.99

1 in stock

Online inventory may differ from in-store availability. 

Fast Shipping

Quick turnaround so you get your gear sooner.

Secure FFL-Friendly Checkout

Trusted checkout with industry-standard protection.

Family-Owned Business

Keeping Traditions Alive Since 1953

Secure Transactions provided with

Description

If you're loading 6.5 PRC for a precision bolt gun and you want more say over neck tension than a standard die gives you, this Forster set is built for exactly that. It combines a Bushing Full Length Sizing Die with the Bench Rest Ultra Micrometer Seater Die, and Forster includes three bushings sized .288, .290, and .292 so you can get working without a separate parts order. Everything comes packaged in Forster's deluxe red die box.

The sizing die works the case body and bumps the shoulder just enough to fit a minimum-spec SAAMI chamber, while the interchangeable bushing handles the neck. Because you pick the bushing, you control how much the neck gets worked and how much tension ends up on the bullet. The usual starting point is a bushing about .002 inch under your loaded round's neck diameter for roughly .002 inch of tension, though hunters often run a touch tighter and benchrest folks sometimes go lighter. Bushings are swappable in .001 inch increments, so the three included sizes give you real room to experiment before buying anything else. Working the neck less this way is easy on your brass and tends to keep necks straighter, which pays off in case life and consistency.

What the Forster 6.5 PRC Bushing Die Set Brings to the Bench

Forster has been machining reloading tools in Lanark, Illinois since 1938, and the fit and finish here reflects it. The bushings are polished smooth for clean neck sizing, and the die body is steel.

Dialing in Seating Depth with the Ultra Micrometer Seater

The Bench Rest Ultra Micrometer Seater is a non-crimping, straight-line seater that holds the bullet and case in alignment while the bullet is press-fit seated. Once you've seated a dummy round and measured it, you just turn the micrometer stem to your target depth and the next round comes out right where you want it. For chasing lands and tweaking jump, that repeatable adjustment is the part most reloaders end up appreciating most.

Key Specifications

  • Cartridge: 6.5 PRC
  • Die Style: 2-Die Set
  • Sizing Die: Bushing Full Length Sizing Die
  • Seater Die: Bench Rest Ultra Micrometer Seater Die
  • Bushings Included: .288, .290, .292
  • Bushing Compatibility: Forster neck sizing bushings
  • Thread: 7/8-14
  • Material: Steel
  • Country of Origin: USA
  • Manufacturer: Forster Products
  • Manufacturer Part Number: UFB4409
  • UPC: 757253990465

What’s Included

  • Bushing Full Length Sizing Die
  • Bench Rest Ultra Micrometer Seater Die
  • Three neck bushings (.288, .290, .292)
  • Deluxe die box

Frequently Asked Questions

Which bushings come with the Forster 6.5 PRC Bushing Die Set?

The set ships with three Forster bushings sized .288, .290, and .292. That spread lets you move up or down in .001 inch steps to tune neck tension for your brass. For most loads, you'll start around .002 inch under your loaded round's neck diameter, which usually lands right in the included range.

How do I pick the right bushing size?

Measure the neck diameter of a loaded round with the bullet seated, then subtract your desired neck tension. Subtracting about .002 inch is a common starting point that keeps bullets secure without overworking the brass. Hunters sometimes prefer a little more tension while benchrest reloaders often run less, so a test round and a caliper will confirm where you land.

Does the Ultra Micrometer Seater Die crimp?

No, it's a non-crimping, straight-line seater that holds the bullet and case in alignment while the bullet is press-fit seated. After you seat a dummy round and measure it, you adjust the micrometer stem up or down to hit your exact seating depth. That makes dialing in jump to the lands quick and repeatable.

Will these dies work in a non-Forster press?

Yes. The dies use standard 7/8-14 threading, so they fit any common reloading press, as well as Forster's own Co-Ax press. One thing to note: the sizing die is designed for Forster neck bushings, so stick with Forster bushings if you add sizes down the road.

Additional information

UPC

757253990465

Manufacturer

Manufacturer Part Number

UFB4409

Shipping Weight

1.475

Reviews

There are no reviews yet.

Be the first to review “Forster 6.5 PRC Bushing Full Length Die Set, 2-Die w/ Bushings”