Description
Forster built this Bushing Full Length Sizing Die for the reloader who wants real control over how their .338 Lapua Magnum brass comes out of the press. Instead of a fixed neck diameter, you drop in one of the included bushings to set your exact neck tension, while the die still sizes the body, bumps the shoulder back to headspace, deprimes the case, and expands the neck as it withdraws. For a big magnum like the .338 Lapua, where quality brass is an investment, that extra control pays off over the life of your cases.
What the .338 Lapua Bushing Die Actually Does
This is a full-length die, so it works the whole case rather than just the neck. The body and shoulder get sized down just enough to chamber cleanly in a minimum SAAMI-spec rifle, and the bushing limits how much the neck gets worked. Because the neck isn't overworked, your brass tends to last longer and your loaded rounds stay more consistent from one to the next. The kit ships with three bushings sized .360, .362, and .364, which cover the range most .338 Lapua handloaders reach for first.
Picking the Right Bushing for Your Brass
Bushings come in .001 inch steps, so you can fine-tune neck tension to match your brass thickness and your rifle. Around .002 inch of neck tension is a common starting point, though hunters and field loaders often run a touch tighter. As brass work-hardens after several firings, you may find yourself stepping down to a smaller bushing to keep the same grip. The die is machined by hand with Forster's one-piece reamers and includes the E-Z Out floating expander ball to help keep necks concentric on the way out.
Press Setup
For anyone running a Forster Co-Ax press, no shellholder is needed thanks to the sliding jaw design. If you're using a standard 7/8-14 threaded press, just add the shellholder recommended for the .338 Lapua case head and you're set. Made in the U.S.A. and backed by Forster's reputation for match-grade tooling.
Key Specifications
- Cartridge: .338 Lapua Magnum
- Die Style: Bushing Full Length Sizing Die
- Bushings Included: Three (.360, .362, .364)
- Bushing Increments: 0.001 inch
- Expander System: E-Z Out Floating Expander Ball
- Thread: 7/8-14 (also fits Forster Co-Ax)
- Manufacturer: Forster Products
- Manufacturer Part Number: FBK4901
- UPC: 757253989988
- Country of Origin: Made in the U.S.A.
- Shipping Weight: 0.55 lb
What’s Included
- One Forster Bushing Full Length Sizing Die for .338 Lapua Magnum
- Three neck bushings (.360, .362, .364)
- Decapping/expander assembly
- Die lock ring
- Instructions
Frequently Asked Questions
What bushings come with the .338 Lapua Forster kit?
The kit includes three bushings in .360, .362, and .364 diameters. Forster picks these sizes as the ones most .338 Lapua handloaders will reach for based on typical brass. Since bushings step in .001 inch increments, you can add others later to fine-tune neck tension for your specific brass and rifle.
Does this Forster bushing die size the full case or just the neck?
It's a full-length die, so it sizes the neck, body, and shoulder and deprimes in one stroke. The bushing controls how much the neck gets worked while the body and shoulder are sized to fit a minimum SAAMI-spec chamber. That full-length work is why it's a good all-around choice rather than a neck-only die.
Do I need a shellholder to run this die?
If you're using a Forster Co-Ax press, no shellholder is required because the press uses sliding jaws. In any standard 7/8-14 threaded press, you'll want the shellholder your press maker recommends for the .338 Lapua case head. The die itself works in both setups.
How do I know which bushing to start with?
A good approach is to measure the neck diameter of a loaded round and subtract the amount of neck tension you want, often around .002 inch to start. Pick the bushing closest to that number. As your brass work-hardens over several firings, you may need to step down to a smaller bushing to keep the same grip.



Reviews
There are no reviews yet.