Description
Thick, uneven case necks are one of those quiet accuracy killers that a lot of reloaders overlook. Too much brass on the inside of the neck can crank up chamber pressure and throw the occasional flyer when you least expect it. The Forster Inside Neck Reamer #308 tackles that problem head on by shaving excess brass from the inner neck walls of your .30 caliber cases, leaving you with cleaner, more uniform necks that grip the bullet consistently shot after shot.
This is the NR1308, finished to a .3110" reaming diameter for use with .308" bullets. Like all of Forster's standard neck reamers, it's ground roughly .0025" to .003" over the max bullet diameter, so you get proper clearance without over-thinning the brass. The staggered tooth design is the real highlight here, cutting through brass smoothly without the chatter that leaves a rough, inconsistent inner wall.
How the Forster #308 Neck Reamer Fits Into Your Press
The reamer isn't a standalone gadget. It drops into the cutter of your Forster Original, Classic, or Power Case Trimmer in place of the pilot. If you already run a Forster trimmer, this is a natural add-on that extends what your setup can do. Slide the shank into the cutter shaft, snug the set screw, and you're ready to ream.
Getting the Most From the .3110" Inside Neck Reamer
Timing matters with neck reaming. Forster recommends using a standard reamer after the case has been fired with a full load and before you run your neck or full-length sizing step. A handy rule of thumb is to ream after firing and turn after sizing. Brush the chips away between cases to keep the cut clean, and you'll end up with necks that are uniform in thickness and far more consistent at the bench.
Built from high-grade, wear-resistant tool steel and made in the USA, this little tool earns its spot in the toolbox for anyone chasing tighter groups out of their .30 caliber loads.
Key Specifications
- Manufacturer: Forster Products
- Manufacturer Part Number: NR1308
- UPC: 757253004940
- Caliber: .30 Caliber (.308" bullets)
- Reamer Finished Diameter: 0.3110"
- Grind Tolerance: Ground .0025" to .003" over max bullet diameter
- Tooth Design: Staggered tooth for smooth, chatter-free cutting
- Material: High-grade, wear-resistant tool steel
- Compatibility: Forster Original, Classic, and Power Case Trimmers
- Country of Origin: USA
- Quantity: 1
What’s Included
- Forster Inside Neck Reamer #308 (.3110") for .30 Caliber
Frequently Asked Questions
What does the Forster #308 Inside Neck Reamer actually do?
It removes excess brass from the inside walls of the case neck on .30 caliber cases. Thick necks can raise chamber pressure and cause flyers, so reaming them to a consistent thickness helps your reloads chamber properly and shoot more accurately. The .3110" finished diameter is sized for .308" bullets.
Do I need a Forster case trimmer to use this reamer?
Yes. The reamer mounts in the cutter of a Forster Original, Classic, or Power Case Trimmer in place of the pilot. The shank slides into the cutter shaft and locks down with the set screw, so you'll want one of those trimmers to run it.
When should I use the neck reamer during my reloading process?
Forster recommends using a standard neck reamer after the case has been fired with a full load and before your neck or full-length sizing step. A good rule of thumb is to ream after firing and turn after sizing. Brushing chips away between cases keeps the cut clean and consistent.
What is the difference between the reamer size and the bullet size?
The NR1308 is ground to a .3110" finished diameter for use with .308" bullets. Forster grinds their standard reamers roughly .0025" to .003" over the maximum bullet diameter, which gives the right clearance without thinning the brass too much.




Reviews
There are no reviews yet.