0
0

Lee Collet Neck Sizer Die .300 Win Mag (Die Only) – 90961

UPC: 734307909611

$19.99

48 in stock

Online inventory may differ from in-store availability. 

Fast Shipping

Quick turnaround so you get your gear sooner.

Secure FFL-Friendly Checkout

Trusted checkout with industry-standard protection.

Family-Owned Business

Keeping Traditions Alive Since 1953

Secure Transactions provided with

Description

The Lee Collet Neck Sizer Die handles one job and does it well: sizing only the neck of your fired .300 Winchester Magnum brass. Instead of squeezing the neck down and then dragging an expander ball back through it like a conventional neck die, this one presses the neck against a central mandrel using four collet fingers. You end up with a neck that's sized evenly from top to bottom, dead straight, with very little runout and no case lube required. For folks running a bolt gun and loading brass fired in that same rifle, it's one of the simplest ways to build accurate ammo.

How the .300 Win Mag Collet Die Works

The magic is in the mechanics. Four collet petals clamp the neck around a hardened mandrel, forming the brass to a consistent inside diameter. Because the brass springs back slightly after sizing, you don't need lube, and you skip the cleanup that comes with it. Neck sizing like this preserves the fire-formed fit of the case body, so the brass stays matched to your chamber and tends to last noticeably longer than full-length sized cases. One tip worth knowing: these dies run on press feel rather than a hard cam-over, so give the handle a firm, consistent squeeze (think 20 to 25 pounds) and you'll get repeatable neck tension round after round.

Getting the Most From Your Lee Collet Neck Sizer

A common trick among handloaders is to size, back the case out about an inch, rotate it an eighth of a turn, and size again. That lands the petals on fresh high spots and gives you an even rounder neck. If you want to fine-tune tension, the mandrel is the key: a slightly smaller mandrel means more grip on the bullet. The die uses the standard 7/8-14 thread, so it threads right into any common single-stage press. Keep in mind this is the die only, so you'll pair it with your own shell holder and a seating die to finish the round. It's built for cases fired in your own gun and best suited to bolt actions rather than autoloaders or lever guns.

Key Specifications

  • Manufacturer: Lee Precision
  • Manufacturer Part Number: 90961
  • UPC: 734307909611
  • Caliber: .300 Winchester Magnum
  • Die Type: Collet Neck Sizer
  • Material: Steel
  • Thread: 7/8-14 (standard)
  • Sizing Method: Collet squeezes neck against precision mandrel
  • Case Lube Required: No
  • Configuration: Die Only (single die)
  • Best Suited For: Bolt-action rifles

What’s Included

  • Lee Collet Neck Sizer Die (.300 Win Mag)
  • Instruction sheet

Frequently Asked Questions

Do I need case lube with the Lee Collet Neck Sizer Die?

No, this die requires no lubrication. Because the collet squeezes the neck against a mandrel and the brass springs back slightly, there's no sticking and no lube to wipe off afterward. That also means no greasy cleanup step between loading sessions.

Does the .300 Win Mag Collet Die full-length size the case?

No, it sizes the neck only. The case body stays in its fire-formed condition, which keeps the brass matched to your chamber and helps it last longer. For that reason it's intended for cases that were fired in the same rifle you're loading for, and it's best used with bolt actions.

Is a seating die or shell holder included with this die?

No, this is sold as the die only. You'll use it with your own shell holder and a separate bullet seating die to complete the round. It threads into any standard press thanks to the common 7/8-14 thread.

How do I adjust neck tension with the Lee Collet die?

The die doesn't have a mechanical tension dial, so tension is driven by the mandrel diameter and your press stroke. Give the handle a firm, consistent squeeze each time for repeatable results. If you want more grip on the bullet, a slightly smaller mandrel will increase neck tension.

Additional information

UPC

734307909611

Manufacturer

Manufacturer Part Number

90961

Caliber/Gauge

.300 Winchester Magnum

Length

4.9000

Product Type

Collet Neck Sizing Rifle Die

Shipping Weight

0.55

Reviews

There are no reviews yet.

Be the first to review “Lee Collet Neck Sizer Die .300 Win Mag (Die Only) – 90961”