Description
The .32 S&W is one of those classic little cartridges that nobody factory-loads much anymore, so if you shoot an old top-break or a pocket revolver chambered for it, reloading is pretty much the way to keep feeding it. This Lee Carbide 3-Die Set covers that job start to finish. It's built specifically for the .32 S&W (the short case, not the Long), and with a little care the dies can also work on .32 S&W Long brass.
What the Lee .32 S&W Die Set Brings to the Bench
The real star here is the carbide full-length sizing die. The carbide ring means you can resize cases without smearing lube on every one first, which saves a messy step and a tumbling session afterward. Lee grinds these dies with a contour so the sizing is step-less. You won't find that abrupt ring other brands sometimes leave where the die stops. Rounding out the set is a powder-through expanding die that flares and charges the case in one motion when paired with a measure or the included dipper, plus a bullet seating die that handles seating and crimping together.
Why Reloaders Reach for the Lee Carbide 3-Die Set
Lee keeps the expander flare to the minimum needed for easy bullet starting, and the seating die removes that flare on the way, so you don't need a separate taper crimp die for good results. Each die has an enlarged mouth that helps guide in range-beat brass without hanging up. The dies use the standard 7/8-14 thread, so they'll thread right into Lee, Dillon, Hornady, Lyman, RCBS and other common single-stage and turret presses.
One thing worth knowing from folks who load this caliber: the 4.0cc dipper that ships in the box is on the big side for .32 S&W charges, so most people end up reaching for a smaller dipper or dialing in their powder measure. Everything arrives in a fitted storage box, and Lee backs the set with their warranty.
Key Specifications
- Manufacturer: Lee Precision
- Manufacturer Part Number: 90696
- UPC: 734307906962
- Caliber: .32 S&W
- Product Type: Carbide 3-Die Set, Pistol
- Number of Dies: 3
- Die Material: Carbide (sizing ring)
- Thread Size: 7/8-14 standard
- Shell Holder: Included (Universal)
- Intended Use: Pistol / revolver cartridge reloading
- Country of Origin: United States
- Shipping Weight: 1.2 lbs
What’s Included
- Carbide Full-Length Sizing Die
- Powder-Through Expanding Die
- Bullet Seating Die
- Universal Shell Holder
- Powder Dipper
- Instructions and Load Data
- Fitted Storage Box
Frequently Asked Questions
Do I need to lube my cases with the Lee Carbide 3-Die Set?
The carbide ring in the full-length sizing die lets you resize .32 S&W brass without case lube, which is the main perk of going carbide. That saves you the lubing step and the cleanup afterward. You'll still want clean brass and a little care when setting up your dies for best results.
Will this Lee .32 S&W die set work on .32 S&W Long brass?
This set is built for the .32 S&W (short) case. That said, many reloaders use it on .32 S&W Long brass with a bit of care, since the two share the same case diameter. For high-volume .32 S&W Long loading, Lee makes a dedicated set for that cartridge.
Does the Lee Carbide 3-Die Set fit my press?
Yes, the dies use the standard 7/8-14 thread, so they thread into Lee, Dillon, Hornady, Lyman, RCBS and other common presses. It works on single-stage and turret setups alike. You get a universal shell holder in the box, so you're ready to mount up and go.
Is the included powder dipper the right size for .32 S&W?
The set ships with a 4.0cc dipper, which runs large for typical .32 S&W powder charges. Most folks loading this caliber end up using a smaller dipper or a powder measure dialed to their specific load. Always check your load data and verify charges before loading.




Reviews
There are no reviews yet.