Description
The Lee Precision Pacesetter 3-Die Set covers the full cycle of loading .270 Winchester, from resizing fired brass to seating and crimping your bullet. If you're reloading one of the all-time great deer and elk rounds, this set gives you the three dies that matter plus the small extras that make setup painless. The whole kit lives in a compartmentalized storage box with a clear lid, so your dies and shell holder stay organized on the bench.
What Comes in the Lee Pacesetter .270 Die Set
You get a full-length sizing die with a built-in stuck case remover, an Easy Adjust Dead Length bullet seating die, and the Lee Factory Crimp Die. The seating die handles just about any bullet point style, and depth is set with a simple adjustment rather than fussy guesswork. The sizer brings fired brass back to spec so your loaded rounds chamber cleanly in any .270 Winchester rifle.
Why the Factory Crimp Die Earns Its Keep
The Factory Crimp Die is the piece that sets Lee's Pacesetter sets apart. It applies a segmented, collet-style crimp similar to what you see on factory ammo, and it's tough to buckle a case the way you can with a traditional roll crimp. A firm, consistent crimp means pressure builds to a higher level before the bullet moves, which tends to tighten up velocity spreads and helps accuracy, especially on hunting loads that get knocked around in the field. Trim length is also far less critical with this design, so you spend less time babysitting case length.
Built for the .270 Winchester Handloader
The dies are machined from steel and the set includes a universal shell holder, a powder dipper, and an instruction sheet with .270 Winchester load data to get you started. Lee backs every die with a lifetime warranty, so this is a buy-once setup for one of the most popular hunting cartridges out there. Pair it with a single-stage press and your favorite components and you're ready to roll your own.
Key Specifications
- Manufacturer: Lee Precision
- Manufacturer Part Number (MPN): 90505
- UPC: 734307905057
- Series: Pacesetter
- Caliber: .270 Winchester
- Die Count: 3-Die Set
- Die Type: Full Length Sizing
- Product Type: Pacesetter Rifle Dies w/ Shell Holder
- Material: Steel
- Country of Origin: United States
- Warranty: Lifetime
What’s Included
- Full Length Sizing Die with built-in stuck case remover
- Easy Adjust Dead Length Bullet Seating Die
- Lee Factory Crimp Die
- Universal Shell Holder
- Powder Dipper
- Instructions and .270 Winchester load data
- Compartmentalized storage case with clear lid
Frequently Asked Questions
Do I need a separate shell holder for the Lee Pacesetter .270 die set?
No, the set comes with a universal shell holder sized for the .270 Winchester case head, so you can get loading right out of the box. You'll still need a press, a scale or your preferred powder measure, and your components. The included dipper gives you a starting point if you're working off the load data in the box.
What does the Lee Factory Crimp Die do and should I use it?
The Factory Crimp Die applies a controlled, collet-style crimp that locks the bullet in place more firmly than a standard seating die crimp. Many handloaders find it improves consistency and accuracy, and it's especially worth using on hunting ammo that gets handled in the field or run through heavier-recoiling rifles. A crimp isn't mandatory on every bottleneck load, so it's there when you want it.
Will this die set work in my press?
Yes, these use standard 7/8-14 threads and fit the vast majority of single-stage and turret presses on the market. The full-length sizing die also has a built-in stuck case remover, which is a nice bit of insurance if a case ever gets hung up.
Is the seating depth hard to adjust on the Pacesetter seating die?
Not at all. The Easy Adjust Dead Length bullet seating die is set with a simple finger adjustment and works with just about any bullet point style you'd run in a .270 Winchester. Once you dial in your overall length it holds that setting from round to round.



Reviews
There are no reviews yet.