Description
The Lee 90374 double cavity mold is built for the handloader who wants to roll their own .457 diameter, 405 grain flat nose bullets. It drops two bullets per pour, which keeps a casting session moving without turning it into an all day affair. The 405 grain flat nose is the classic 45-70 Government profile, and the same .457 diameter bullet also feeds nicely into the bigger black powder cartridge cases like the 45-90 and 45-110 Sharps if that's your thing.
Why the 90374 Mold Wins on Material
Lee machines these blocks from aluminum, which earns its keep in a few ways. Aluminum won't rust and lead won't stick to it the way it does on steel, and the blocks weigh about a third of what iron or steel molds do, so your hands and forearms don't give out halfway through a big batch. Aluminum also heats up and cools down fast, meaning you're dropping good bullets after just a handful of casts rather than waiting forever for the block to come up to temp.
How the Lee Double Cavity Mold Casts
The cavity halves are clamped together and lathe bored, which holds roundness to .001 or less and keeps bullet diameter consistent across both cavities. There's a tangential cut off design on the sprue plate that trims the nib cleanly so you aren't left with a ragged base. Many 45-70 handloaders pour these, lube, and load without even sizing, which is a real time saver when you're feeding a rifle that likes a fat, soft cast bullet.
Getting Started With Your 90374 Mold
Like any new aluminum mold, this one benefits from a proper break in. Wash and dry the cavities, smoke them lightly with a wooden match, beeswax candle, or butane lighter, then bring your casting speed and heat up gradually. Lee specifically steers folks away from spray type release products, since buildup in the cavity can shrink your bullet diameter. Treat it with a little care and this mold will keep churning out bullets for a long time.
Key Specifications
- Manufacturer: Lee Precision
- Manufacturer Part Number: 90374
- UPC: 734307903749
- Caliber: .45 Caliber (45-70 Government)
- Bullet Diameter: .457 inch
- Bullet Weight: 405 grain
- Bullet Profile: Flat Nose
- Cavities: 2 (Double Cavity)
- Mold Material: Machined Aluminum
- Sprue Plate: Hard Anodized with Tangential Cut Off
- Cavity Roundness: .001 inch or less
- Length: 10.8 inches
- Country of Origin: USA
What’s Included
- Lee 90374 aluminum double cavity bullet mold block
- Mold handles
- Sprue plate
- Instructions
Frequently Asked Questions
What cartridges can I load with the Lee 90374 mold?
This mold casts a .457 diameter, 405 grain flat nose bullet that's the classic load for the 45-70 Government. Because the diameter is the same, these bullets also work in larger black powder cartridge cases like the 45-90, 45-100, and 45-110 Sharps. Always check a current reloading manual or a powder maker's data for the right charge.
Does the Lee double cavity mold come with handles?
Yes, handles and the sprue plate are included, so you have everything you need to start casting. That's a nice bonus since some mold makers sell the blocks and handles separately. You'll just need your own lead pot, alloy, and the usual casting gear.
Do I need to size the bullets after casting?
Many 45-70 handloaders pour these bullets, lube them, and load them straight away without a separate sizing step, which saves a lot of time. Whether you size depends on your rifle's bore and how snug you want the fit. If you do want to size, the .457 diameter drop fits common 45 caliber sizing setups.
How do I break in the Lee 90374 aluminum mold?
Wash and dry the cavities, then lightly smoke them with a wooden match, beeswax candle, or butane lighter before your first pour. Bring your casting speed and heat up gradually to get the blocks to temperature and start dropping good bullets. Lee advises against spray type release products since buildup can shrink your bullet diameter over time.




Reviews
There are no reviews yet.