Description
If you've been fighting flyers with slugs out of a smoothbore Remington barrel, this is one of the cheaper fixes worth trying before you drop the money on a whole rifled barrel. Carlson's rifled choke tube threads into any Rem-Choke pattern 12 gauge and gives Foster-style rifled slugs just enough spin to settle down and hit where you're aiming. It's an extended design that sticks out past the muzzle a bit, which also helps protect the crown of your barrel.
The engineering here is deliberately mellow. The tube runs a slow right-hand 1-in-35 twist with a .730 groove diameter, which imparts enough rotation to steady a slug without stressing the gun the way a fully rifled barrel and hot sabot load would. It's machined from 304 stainless steel and wears a matte black finish that shrugs off corrosion, and Carlson's backs it with a lifetime warranty.
What the Carlson's Rifled Choke Tube Does Best
Where this tube shines is with traditional and rifled Foster slugs, the kind built to stabilize out of a smooth bore in the first place. Guys running Remington Sluggers and Winchester rifled slugs in the 1,600 fps range regularly report groups tightening up dramatically, with plenty seeing solid accuracy out to 75 or even 90 yards where a plain cylinder or improved cylinder choke left them scattered. It's a real, noticeable improvement for the money.
Getting the Most From Your Rifled Rem-Choke Tube
The honest reality with any rifled choke tube is that ammo selection matters a lot, so plan on picking up a couple of slug brands and doing some testing to find what your gun likes. Heavy saboted slugs designed for fully rifled barrels can keyhole through just an inch of rifling, so stick with Foster and rifled slug loads to get the best out of it. Installation is quick with a standard choke wrench, and a dab of choke lube on the threads makes future removal painless.
Key Specifications
- Manufacturer: Carlson's Choke Tubes
- Manufacturer Part Number: 40020
- UPC: 723189400200
- Gauge: 12 Gauge
- Thread Pattern: Remington Rem-Choke
- Constriction Type: Rifled
- Twist Rate: 1-in-35, Right Hand
- Groove Diameter: .730 inches
- Material: 304 Stainless Steel
- Finish: Matte Black
- Style: Extended
- Length: 7.85 inches
- Chokes Included: One Choke
- Warranty: Lifetime
What’s Included
- One Carlson's rifled choke tube
- Standard choke wrench
Frequently Asked Questions
Will this rifled choke tube fit my Remington shotgun?
It's cut for the Remington Rem-Choke thread pattern and fits most 12 gauge Remington models that use those chokes, including the popular 870 and 1100. If your barrel is already threaded for Rem-Choke tubes, this one will thread right in. It's always smart to confirm your barrel takes Rem-Choke chokes before ordering.
What kind of slugs should I run through the Carlson's rifled choke tube?
Stick with Foster-style and rifled slugs, which are the loads built to stabilize out of a smooth bore. Remington Sluggers and Winchester rifled slugs in the 1,600 fps or lower range tend to be crowd favorites through this tube. Heavy saboted slugs meant for fully rifled barrels can tumble through just an inch of rifling, so those are best avoided here.
Can this replace a full rifled barrel?
It's not a substitute for a dedicated rifled slug barrel if you're chasing long-range sabot performance, but it's a fraction of the cost and delivers a real accuracy bump for close to medium range slug hunting. Plenty of hunters get dependable groups out to 75 to 90 yards with the right load. For deer at typical slug distances, it's a smart, budget-friendly upgrade.
Do I need to do anything special to install it?
Not much. It threads in with the included standard choke wrench, and it's an extended tube so it'll stick out past your muzzle by an inch or so. A little choke tube grease on the threads keeps things smooth and makes it easy to swap back out down the road.




Reviews
There are no reviews yet.