Description
When the ducks and geese start hanging up out of range, this is the choke you want threaded into your Browning Invector-Plus 12 gauge. The Cremator Long Range runs a tight .715 constriction that's built to squeeze every bit of reach out of your gun. It's non-ported, machined from heat-treated 17-4 stainless steel, and it wears a matte black finish that shrugs off the abuse of a wet marsh season.
What Makes the Cremator Choke Different
The heart of this tube is Carlson's Triple Shot Technology, or TST. Instead of one abrupt step down to the final constriction, the taper section uses three graduated rings that ease the shot column into the tighter bore gradually. That gentler transition means less pellet deformation, fewer flyers, and a denser, more even pattern downrange. On steel loads especially, this is the kind of design that turns a shot you'd normally pass on into a clean fold.
Built for Long-Range Waterfowl
This is the top-end constriction in the Cremator lineup, made for shots reaching past 40 yards where you need every pellet on the bird you can get. The extended body gives you a 25 percent longer parallel section than a standard flush tube, which is a big part of why these things pattern so tight. The extension also lets you spin it in and out by hand without a wrench, and it adds a little muzzle protection while you're wading through timber and blind edges. It handles steel shot with no size or speed restrictions, so you can load up your favorite waterfowl payload with confidence.
Why Hunters Reach for the Cremator
Carlson's builds these right here in the USA and backs every tube with a lifetime warranty, so if anything ever goes wrong you just send it back for a replacement. It's an easy upgrade over a factory choke and one of the more trusted names when it comes to putting more birds in the bag. Pattern it with the loads you actually hunt, and you'll see exactly why folks keep this one in the vest.
Key Specifications
- Manufacturer: Carlson's Choke Tubes
- Manufacturer Part Number: 11627
- UPC: 723189116279
- Choke System: Browning Invector-Plus
- Gauge: 12 Gauge
- Constriction: Long Range
- Exit Diameter: .715
- Porting: Non-Ported
- Material: Heat-Treated 17-4 Stainless Steel
- Finish: Matte Black
- Style: Extended with Triple Shot Technology (TST)
- Shot Compatibility: Lead and Steel
- Chokes Included: One Choke
- Warranty: Lifetime
- Country of Origin: Made in USA
What’s Included
- One Carlson's Cremator Long Range non-ported choke tube (.715)
- Choke wrench
Frequently Asked Questions
What shotguns does this Cremator choke fit?
This tube is cut for the Browning Invector-Plus 12 gauge choke system. That includes many Browning and Winchester models that use Invector-Plus threading. If you're unsure, check your barrel or owner's manual for the Invector-Plus marking before ordering.
Can I run steel shot through the Cremator Long Range choke?
Yes. The Cremator series carries no size or speed restrictions with steel shot in this long-range constriction, so you can load up your usual waterfowl payloads. It's machined from heat-treated 17-4 stainless steel specifically to hold up to hard-hitting steel loads.
What is the .715 constriction good for?
The .715 diameter is the tightest, longest-range option in the Cremator lineup for this gun. It's built to hold a dense pattern on birds out past 40 yards, which makes it a strong pick for late-season ducks and geese that hang up out of range. For decoying birds inside 30 yards you may want a more open mid-range tube.
Is this choke ported, and does it come with a wrench?
This is the non-ported version, which keeps things a little quieter and doesn't kick up debris in a blind. It ships with a choke wrench, though the extended design also lets you install and remove it by hand.



Reviews
There are no reviews yet.