Description
The 7x57mm Mauser has been quietly impressing handloaders for well over a century, and it's one of those rounds that rewards careful reloading. Redding's Series A Full Length Die Set gives you the two tools you need to run that classic cartridge from start to finish. It's a two-die setup built for bottleneck brass, with every piece machined to the kind of tolerances that have made Redding a go-to name on the reloading bench for decades.
What the Redding 7×57 Die Set Does on the Bench
The full-length sizing die works the entire body of the case and bumps the shoulder back, resetting headspace so your loaded rounds chamber smoothly. It comes fitted with a decapping rod assembly that carries a neck expander button and decapping pin, so you knock out the spent primer and open the case neck in one stroke. The bullet seating die rounds out the set with a bullet guide, a built-in crimp ring, and a seating plug, and you dial in your seating depth simply by threading the plug in or out.
Why Reloaders Reach for the Redding Series A Set
Full-length sizing is the practical choice when you want brass that feeds reliably across a single rifle or several rifles sharing the same chambering. That makes this set a sensible pick for hunting loads you need to trust in the field. The 7×57 takes well to handloading and runs happily with bullets anywhere from 120 to 175 grains, so you've got plenty of room to tune a load for deer, pronghorn, hogs, or plains game.
Getting the Most From Your 7x57mm Mauser Reloads
A quick heads-up worth knowing: this set does not include a shell holder, which is sold separately. The 7×57 uses a Redding #1 shell holder if you're building out your setup. Pair these dies with quality brass and good load data, and you'll have a classic cartridge dialed in tight.
Key Specifications
- Manufacturer: Redding
- Cartridge: 7x57mm Mauser (7mm Mauser)
- Die Set Type: Series A Full Length 2-Die Set
- Case Type: Bottleneck
- Dies Included: Full Length Resizing Die, Bullet Seating Die
- Bullet Diameter: 0.284"
- Shell Holder: Redding #1 (sold separately)
- Thread Size: 7/8"-14
- Manufacturer Part Number: 80138
- UPC: 611760801389
- Shipping Weight: 1.28 lbs
What’s Included
- Full Length Resizing Die with decapping rod assembly, neck expander (size button) and decapping pin
- Standard Bullet Seating Die with bullet guide, built-in crimp ring and seating plug
- Die box
Frequently Asked Questions
Does the Redding 7x57mm Mauser die set come with a shell holder?
No, the shell holder is sold separately with this set. The 7x57mm Mauser uses a Redding #1 shell holder. If you're new to the cartridge or starting fresh, pick one up at the same time so you're ready to load.
What exactly is included in this Series A full length die set?
You get two dies: a full-length resizing die and a bullet seating die. The sizing die carries a decapping rod assembly with a neck expander button and decapping pin, while the seating die includes a bullet guide, built-in crimp ring, and seating plug. It covers the full sizing and seating process for 7x57mm Mauser brass.
What bullet weights work well when reloading 7x57mm Mauser with these dies?
The 7x57mm Mauser commonly runs bullets from 120 to 175 grains. Lighter bullets suit deer and pronghorn-sized game, while heavier 160 to 175 grain projectiles give you deeper penetration for larger animals. Always follow published load data for your specific bullet and rifle.
Can I use this Redding set to reload for more than one 7×57 rifle?
Yes. Because it full-length sizes the case and sets the shoulder back, the brass is sized to feed reliably in any rifle chambered for the same cartridge, not just one specific chamber. That flexibility is one of the main reasons reloaders choose full length sets for hunting ammo.





Reviews
There are no reviews yet.