0
0

RCBS 2-Die Full-Length Die Set 6.8 Western | Sizer & Seater

UPC: 604544679298

$52.99

16 in stock

Online inventory may differ from in-store availability. 

Fast Shipping

Quick turnaround so you get your gear sooner.

Secure FFL-Friendly Checkout

Trusted checkout with industry-standard protection.

Family-Owned Business

Keeping Traditions Alive Since 1953

Secure Transactions provided with

Description

If you're feeding a 6.8 Western and want to take control of your ammo, this RCBS two-die set is where a lot of handloaders start. It covers the two most important jobs in the reloading cycle: bringing fired brass back to spec and seating bullets to the depth you want. These dies are machined from RCBS proprietary die steel and finished to tight tolerances, so the fit and feel hold up load after load.

What the RCBS 6.8 Western Die Set Does on the Press

The full-length sizer die works the outside of the case, deprimes the spent primer, and runs the neck over the expander ball so it's ready to accept a bullet. It brings brass back to SAAMI minimum cartridge dimensions while holding headspace at minimum tolerances, which keeps the case body length from drifting during sizing. Vents cut into the die let trapped air and extra case lube escape, so you avoid dented shoulders and stuck cases. Full-length sizing is the go-to choice when you're loading for a semi-auto, running ammo across multiple rifles, or just want brass that chambers smoothly every time.

Seating and Crimping with the 6.8 Western Set

The seater die uses a bullet seater plug to push the projectile to your chosen depth, and it has a built-in roll crimper so you can crimp in the same stroke if your load calls for it. Want to seat without crimping? Just back the die body off until the crimp shoulder no longer touches the case mouth, and you're seating only. That flexibility makes it easy to dial in anything from target loads to hard-kicking hunting rounds where bullet pull matters.

Fitting the RCBS 6.8 Western Dies to Your Setup

These dies use the standard 7/8-14 thread, so they'll thread right into any common single-stage, turret, or progressive press. The 6.8 Western shares a case head with the WSM family, so you'll want an RCBS #43 shell holder to run them. The set ships in the familiar green RCBS die box that keeps everything organized on the bench. Shell holder and components are sold separately.

Key Specifications

  • Manufacturer: RCBS
  • Manufacturer Part Number (MPN): 28201
  • UPC: 604544679298
  • Caliber: 6.8 Western
  • Product Type: Full-Length Die Set
  • Dies in Set: 2 (Full-Length Sizer, Bullet Seater)
  • Thread: Standard 7/8-14
  • Die Material: RCBS Proprietary Die Steel
  • Crimp: Built-in roll crimp in seater die
  • Recommended Shell Holder: RCBS #43 (sold separately)
  • Storage: Green RCBS die box
  • Shipping Weight: 1.185 lbs

What’s Included

  • Full-Length Sizer Die with Expander-Decapping Unit
  • Seater Die with Bullet Seater Plug and built-in roll crimper
  • Green RCBS die storage box

Frequently Asked Questions

What shell holder do I need for the RCBS 6.8 Western die set?

The 6.8 Western uses the RCBS #43 shell holder, which is the same one that fits the WSM family of cartridges since they share a case head. The shell holder is not included with this die set and needs to be purchased separately. Make sure you have the right one on hand before you start a session.

Can I seat bullets without crimping with this RCBS 6.8 Western set?

Yes. The seater die has a built-in roll crimper, but you can seat without crimping by backing the die body off until the crimp shoulder no longer contacts the case mouth. That lets you seat only when your load doesn't call for a crimp, then dial the crimp back in when you want it.

Will these dies fit my press?

The set uses the standard 7/8-14 thread, so it will thread into virtually any common single-stage, turret, or progressive reloading press. There's no special press or adapter needed to run them.

What does the full-length sizer die actually do?

It resizes the outside of the case back to SAAMI minimum dimensions, deprimes the spent primer, and expands the neck so it's ready to take a new bullet. It also holds headspace to minimum tolerances and has vents to release trapped air and excess lube. Full-length sizing is the best bet when you want brass that chambers reliably across rifles or in a semi-auto.

Additional information

UPC

604544679298

Manufacturer

Manufacturer Part Number

28201

Caliber/Gauge

6.8 Western

Length

5.9500

Product Type

FULL LENGTH

Shipping Weight

1.185

Reviews

There are no reviews yet.

Be the first to review “RCBS 2-Die Full-Length Die Set 6.8 Western | Sizer & Seater”