Description
The RCBS Matchmaster Neck-Size Bushing Die Set in .30-06 Springfield is aimed squarely at the handloader chasing tight groups and long case life. Instead of full-length resizing, this set works only the case neck, leaving the fired body dimensions alone so your brass stays fitted to your chamber. That approach keeps the metal from being overworked and helps your cases last through more loading cycles, which is exactly what benchrest and long-range crowds have leaned on for years.
What Sets the Matchmaster Neck-Size Die Apart
The heart of this set is the interchangeable neck bushing system. By swapping bushings, you set the exact amount of neck tension on the bullet rather than taking whatever a fixed die hands you. The sizing die also carries a Titanium Carbo-Nitride coated expander, which cuts down on brass buildup and gives you that smooth case extraction on the upstroke. The neck bushings are sold separately, so you can match the bushing to your brass and bullet combination. A good starting point is measuring the outside neck diameter of a loaded round and subtracting about .002 to .003 inch to account for brass springback.
Seating Bullets With the Matchmaster Die
The seater die is where the fit and finish really shows. It uses a large oversized micrometer with clear hash marks, so dialing seating depth to a thousandth of an inch is quick and repeatable. There's also a free-floating, self-centering seating stem that helps keep runout low and concentricity high. The loading window is a nice touch too. You drop the bullet in through the side and run the press, no more balancing a bullet on the case mouth.
Built the Way RCBS Builds Dies
Each die body is machined from case-hardened steel, with the internal surfaces precision-drilled, reamed, and hand polished. The dies run standard 7/8-14 threads, so they thread right into any common single stage or turret press. Made in the USA and backed by the RCBS limited lifetime warranty, this is a set you set up once and keep using for a long time.
Key Specifications
- Manufacturer: RCBS
- Series: Matchmaster
- Caliber: .30-06 Springfield
- Die Type: Neck-Size Bushing, Micrometer Bullet Seating
- Number of Dies: 2
- Expander: Titanium Carbo-Nitride coated
- Thread Size: 7/8-14
- Neck Bushings: Sold separately
- Country of Origin: USA
- Warranty: Limited Lifetime
- Manufacturer Part Number: 14810
- UPC: 604544654158
- Shipping Weight: 1.465 lbs
What’s Included
- Matchmaster neck sizing die
- Matchmaster micrometer bullet seating die
- Spare decapping/expander stem assembly
- Instruction manual
- Reloading data sheet
Frequently Asked Questions
Do neck bushings come with the Matchmaster Neck-Size Die Set?
No, the neck bushings are sold separately so you can match the bushing to your exact brass and bullet setup. To pick the right size, measure the outside neck diameter of a loaded cartridge and subtract about .002 to .003 inch for brass springback. This lets you fine-tune neck tension instead of settling for a fixed amount.
What is the difference between this neck-size set and the full-length Matchmaster set?
This set only sizes the case neck and leaves the fired body dimensions untouched, which keeps brass fitted to your chamber and extends case life. The full-length version resizes the entire case body back toward factory spec. Neck sizing is popular with precision shooters running the same brass through the same rifle, while full-length sizing is better when you need reliable chambering across different rifles.
Will the Matchmaster dies fit my press?
Yes, these dies use standard 7/8-14 threads, so they thread into any common single stage, turret, or progressive press that accepts that size. No special adapters are needed.
What does the Titanium Carbo-Nitride expander do?
The coated expander ball reduces brass buildup and gives you smoother, more consistent case extraction on the upstroke. It also helps keep the case neck from getting overworked, which supports better neck tension consistency and longer case life.




Reviews
There are no reviews yet.