Description
Both the 10mm Auto and .40 S&W share the same .400 bullet diameter, which means this single Hornady Series II set covers you for both cartridges. It's a smart pickup if you shoot either round, since you're getting one set of dies that handles the full-house 10mm loads and the mellower .40 brass alike. Each die threads into any standard single stage or progressive press that takes 7/8-14 dies.
What You Get in the Hornady Series II 3-Die Set
The set comes with three dies: a full-length sizing die, a pistol-style expander die, and a seating die. The sizing die carries Hornady's titanium nitride finish, that gold-ringed coating that's harder than carbide and lets you size straight-walled pistol brass without any case lube. That's the big draw for high-volume handgun loaders, since skipping the lube step speeds up your whole process and keeps your cases clean. Reloaders who have run both consistently note the nitride die sizes with noticeably less effort than carbide dies.
Features That Make the Series II Dies Easy to Live With
The sizing die uses Hornady's Zip Spindle design, which puts a series of light threads on the spindle and collet so it locks down tight and won't slip when you're setting decapping depth. The expander puts a clean, consistent flare on the case mouth so bullets start straight and feed right. Up top, the seating die has a floating alignment sleeve that pre-aligns the bullet with the case before it seats, which helps keep your rounds concentric and consistent. A locking retainer ring at the base of the seater pops out in seconds when it's time to clean things up.
Built to Last Behind the Bench
Everything ships in a compartmentalized storage box that keeps the dies, lock rings, and small parts organized. Each die wears a Sure-Loc lock ring that clamps evenly around the threads to hold your setting without chewing up the die body. Hornady backs the Custom Grade line with a no-risk lifetime warranty, so these are dies you set up once and keep using for years. Worth noting: a shell holder is not included, so grab the right one for your press and the .40/.400 case head if you don't already have it.
Key Specifications
- Manufacturer: Hornady
- Manufacturer Part Number: 546533
- UPC: 090255565331
- Product Type: 3-Die Set
- Caliber: 10mm Auto / .40 S&W
- Bullet Diameter: .400
- Die Series: Series II Custom Grade
- Included Dies: Full-Length Sizer, Expander, Seater
- Sizing Die Finish: Titanium Nitride (no case lube needed)
- Thread Size: 7/8-14
- Spindle Design: Zip Spindle
- Lock Rings: Sure-Loc
- Shell Holder Included: No
- Storage Box: Yes
- Warranty: No-Risk Lifetime Warranty
What’s Included
- Full-length titanium nitride sizing die with Zip Spindle and Sure-Loc lock ring
- Pistol-style expander die with Sure-Loc lock ring
- Bullet seating die with floating alignment sleeve and Sure-Loc lock ring
- Decap pin retainer and headed decap pins
- Compartmentalized die storage box
Frequently Asked Questions
Does this die set work for both 10mm Auto and .40 S&W?
Yes. Both cartridges use the same .400 bullet diameter and the same case diameter, so this one set loads both rounds. You just adjust your seating depth and powder charge to match whichever cartridge and load you're working up.
Do I need case lube with the Hornady Series II sizing die?
No. The sizing die uses Hornady's titanium nitride coating, which is harder than carbide and lets you size straight-walled pistol brass dry. Plenty of loaders report it sizes with less effort than comparable carbide dies, and it keeps your cases clean through the process.
Is a shell holder included with this set?
No, a shell holder does not come in the box. You'll want the correct shell holder for the .40 S&W and 10mm case head along with the right one for your press. If you already load similar cartridges, there's a good chance you have what you need on hand.
Will these dies fit my press?
They use the industry-standard 7/8-14 thread, so they'll thread into any single stage or progressive press that accepts standard dies. If you run a modern Hornady Lock-N-Load press, you'll want the appropriate Lock-N-Load die bushings to swap them in and out quickly.




Reviews
There are no reviews yet.