Description
The 8.6 Blackout thrives on heavy .338 bullets, often running from 285 to 350 grains for subsonic duty and lighter 160 to 225 grain projectiles when you want supersonic velocity. Seating those long, heavy bullets straight is where a quality die earns its keep, and that's exactly what the Hornady Custom Grade seater is built to do. This is a single bullet seating die cut for the .338-inch (8.58mm) bullet diameter the cartridge runs on.
What Sets the Custom Grade 8.6 Blackout Seater Apart
The heart of this die is Hornady's in-line bullet seating system. A floating sleeve captures the bullet, case neck, and seating stem and holds them in perfect alignment before the bullet ever starts into the case mouth. That pre-alignment keeps bullets from entering crooked, which cuts down on runout and helps every round leave the die consistent. For a cartridge that leans so hard on long, heavy-for-caliber bullets, that straightness pays off on paper.
Dialing In Your 8.6 Blackout Seating Depth
The seater adjustment screw makes it easy to set and fine-tune seating depth, and a built-in compression lock o-ring gives you the tension to make those small adjustments stick without drifting. The die ships with a Sure-Loc lock ring that clamps around the entire die body with constant pressure, so once your setup is dialed, it stays put from session to session. A locking retainer ring near the base pops off in seconds when it's time to pull the die apart for cleaning.
Fit and Build
This die uses standard 7/8-14 threads, so it drops right into any common single-stage or progressive press. Like the rest of the Custom Grade line, it's precision machined with one of the smoother internal finishes you'll find, and it's backed by Hornady's no-risk lifetime warranty. Whether you're building quiet subsonic rounds for suppressed work or working up a supersonic hunting load, this seater is a solid foundation for repeatable, accurate 8.6 Blackout ammo.
Key Specifications
- Manufacturer: Hornady
- Product Line: Custom Grade
- Cartridge: 8.6 Blackout (.338 ARC compatible)
- Bullet Diameter: .338 in (8.58mm)
- Die Type: Bullet Seating Die
- Number of Dies: 1
- Die Series: III
- Thread Size: 7/8-14
- Lock Ring: Sure-Loc
- Bullet Puller Collet: #9 (392162)
- Manufacturer Part Number: 044390
- UPC: 090255443905
- Warranty: Lifetime
What’s Included
- Hornady Custom Grade 8.6 Blackout Bullet Seating Die
- Sure-Loc lock ring
Frequently Asked Questions
Does the 8.6 Blackout seater die come as a single die or a full set?
This is a single bullet seating die, not a complete die set. If you're building a full reloading setup for 8.6 Blackout, you'll also want a sizing die to go with it. Hornady offers a matching full length sizing die for the cartridge.
What bullet diameter does this Hornady 8.6 Blackout die use?
It's set up for .338-inch (8.58mm) bullets, which is the standard diameter for the 8.6 Blackout cartridge. That covers the full range of .338 projectiles reloaders use, from lighter supersonic bullets around 160 to 225 grains up to heavy subsonic bullets in the 285 to 350 grain range.
Will this die fit a standard reloading press?
Yes. It uses common 7/8-14 threads, so it threads into just about any standard single-stage or progressive press. The included Sure-Loc lock ring clamps around the full die body to hold your adjustment in place.
What makes the Custom Grade seater good for the long bullets 8.6 Blackout uses?
The die features an in-line seating system where a floating sleeve aligns the bullet, case neck, and seating stem before the bullet enters the case. That keeps those long, heavy .338 bullets going in straight, which reduces runout and helps your accuracy. It matters even more with a cartridge that relies so heavily on long subsonic projectiles.





Reviews
There are no reviews yet.