Description
If you load straight-wall semi-auto pistol brass, a proper taper crimp is what separates rounds that chamber every time from ones that hang up at the feed ramp. The Hornady 044170 Taper Crimp Die handles exactly that job. It removes the case-mouth flare left over from your expander step and tapers the brass snugly against the bullet, all while keeping a crisp edge at the mouth so the cartridge headspaces correctly on rimless auto cases. That matters, because 9mm, 38 Super, and 380 Auto all headspace off the case mouth, which is why you want a taper crimp here and not a roll crimp.
This one covers a lot of ground. The .355 die works for 9mm Luger, 38 Super, and 380 Auto, so if you load more than one of those calibers you can get away with a single tool. It threads into any standard 7/8"-14 press and ships with a Hornady Sure-Loc locking ring, so once you dial in your crimp it stays put from session to session.
Where the 044170 Taper Crimp Die Fits In Your Setup
Hornady's Series II 3-die pistol sets use a seat die that can seat and crimp in one pass, but a lot of reloaders prefer to split those two steps. Adding this die lets you seat the bullet in one station and apply the crimp in another, which gives you tighter control over both and is especially handy on progressive presses. It's a popular upgrade for folks who want their crimp dialed in independently of seating depth.
Build and Fit of the Hornady Taper Crimp Die
This is a single-die unit machined from high-quality steel and backed by Hornady's lifetime warranty. Keep in mind the shellholder is sold separately, since the correct one depends on your caliber and press. Set your crimp by feel and a few test rounds, check them in your barrel or a case gauge, and you'll have ammo that drops in clean and runs without a hitch.
Key Specifications
- Manufacturer: Hornady
- Manufacturer Part Number: 044170
- UPC: 090255441703
- Die Type: Taper Crimp Die
- Calibers: 9mm Luger, 38 Super, 380 Auto (.355)
- Number of Dies: 1
- Thread: 7/8"-14
- Material: High-quality steel
- Gun Type: Semi-automatic pistol
- Shellholder Included: No
- Storage Box Included: Yes
- Warranty: Hornady Lifetime Warranty
- Country of Origin: United States
- Shipping Weight: 0.45 lb
What’s Included
- Hornady taper crimp die (1)
- Hornady Sure-Loc die locking ring
- Storage box
Frequently Asked Questions
What calibers does the Hornady 044170 taper crimp die work with?
This .355 die is set up for 9mm Luger, 38 Super, and 380 Auto. One tool covers all three, which is handy if you load more than one of those cartridges. Just remember the shellholder is caliber and press specific and is sold separately.
Why use a taper crimp instead of a roll crimp on these cartridges?
9mm, 38 Super, and 380 Auto are rimless cases that headspace off the case mouth. A taper crimp removes the flare and squeezes the brass against the bullet while leaving a clean, sharp edge at the mouth for correct headspacing. A roll crimp would curl that edge over and cause chambering and function problems on auto-pistol rounds.
Can I add this to my Hornady Series II 3-die pistol set?
Yes, that's one of the most common uses for it. The seat die in a 3-die set can seat and crimp together, but adding this die lets you crimp in a separate station for more precise, independent control. It's a popular move on progressive presses where you want a dedicated crimp stage.
Does the Hornady taper crimp die come with a shellholder?
No, the shellholder is not included and is sold separately. The die itself ships with a Hornady Sure-Loc locking ring and threads into any standard 7/8"-14 press. Pick up the correct shellholder for your caliber and you're ready to go.



Reviews
There are no reviews yet.