Description
The RCBS X Die Full Length Die Set for .300 Weatherby Magnum is built around one simple goal: cutting down the brass trimming chore that comes with reloading a hard-working magnum cartridge. The set includes the X Die full length sizer and a standard bullet seater die, giving you everything needed to resize fired brass back to spec and seat your bullets consistently. The magic lives in the sizer's mandrel, which carries an expander ball and decapping pin and is designed to control how far the case mouth grows during each resizing cycle.
What Sets the .300 Wby X Die Apart
Unlike a standard full length sizer where nothing stops the brass from flowing forward, the X Die's mandrel contacts the case mouth and slows that growth. The patented design is not meant to shorten the case; instead, after an initial one-time trim of .020 inch under maximum length, it reins in the stretch so cases stabilize below the trim-to line. Thanks to a tight tolerance between the mandrel and the die's neck wall, the neck doesn't thicken as the case is pushed back, which keeps neck tension and chambering behaving the way you want.
Getting the Most From Your X Die Set
Setup is the key with these dies. You trim the whole lot of brass once to that .020 under max figure, set the die correctly, and then keep that batch of brass together through its loading life. Reloaders who run them this way report cases going multiple firings with no trimming while staying inside spec. The .300 Weatherby is a big case that works brass hard, so a tool that keeps case length in check without constant trimming earns its spot on the bench fast.
If you already own a standard set of .300 Weatherby dies, RCBS notes you can get the same benefit by ordering just the X Die full length sizer on its own. These dies are made in the USA and carry the kind of fit and finish RCBS has built its reputation on over six decades of reloading gear.
Key Specifications
- Manufacturer: RCBS
- Caliber: .300 Weatherby Magnum
- Die Type: Full Length X Die Set (2-die)
- Included Dies: X Die Full Length Sizer + Standard Seater Die
- Case Type: Bottleneck Rifle
- Material: Steel
- Initial Trim Requirement: .020 inch under maximum case length
- Country of Origin: USA
- Manufacturer Part Number: 39212
- UPC: 076683392121
- Shipping Weight: 1.4 lbs
What’s Included
- X Die Full Length Sizer Die (.300 Weatherby Magnum)
- Standard Bullet Seater Die (.300 Weatherby Magnum)
Frequently Asked Questions
How does the RCBS X Die cut down on case trimming for .300 Weatherby?
The X Die sizer uses a special mandrel that contacts the case mouth during resizing and slows how fast the brass grows forward. After you trim your brass one time to .020 inch under max length and set the die correctly, the mandrel keeps the cases from stretching past the trim line. That lets you run the same lot of brass through multiple firings without going back to the trimmer.
What comes in the .300 Weatherby X Die set?
This is a two-die set that includes the X Die full length sizer and a standard bullet seater die. The sizer handles resizing and decapping with its mandrel, expander ball, and decapping pin, while the seater sets your bullets to a consistent depth. It covers the two main steps for loading .300 Weatherby bottleneck brass.
Do I need the full set if I already have .300 Weatherby dies?
Not necessarily. RCBS notes that if you already own a standard set of dies for this caliber, you only need to order the X Die full length sizer by itself to get the trimming benefit. The full set is the way to go if you're starting fresh and want both the sizer and a matched seater.
Does the X Die shorten my .300 Weatherby cases?
No, the X Die is not designed to shorten the case. Its job is to reduce the normal rate of growth as the brass flows during sizing. You still do that single initial trim of .020 inch under maximum, and from there the mandrel keeps the case length in check so it stabilizes below the trim-to length.


Reviews
There are no reviews yet.