Description
If you're running a 7mm Winchester Short Magnum and want to stop paying factory prices, this RCBS Full-Length 2-Die Set is where a lot of handloaders start. It covers the two core steps of loading a bottleneck rifle cartridge: sizing the brass back to spec and seating the bullet. RCBS has been making dies in Oroville, California for decades, and the fit and finish here reflect that track record. These dies use the standard 7/8"-14 thread, so they'll thread right into any common single-stage or turret press from RCBS, Lee, Hornady, Lyman, and the rest.
What the 7mm WSM Sizer Die Does
The Full-Length Sizer brings fired cases back down to SAAMI minimum dimensions, working the outside of the case body and neck while it de-primes and runs the expander through to open the neck for a new bullet. Headspace is held to tight tolerances so you're not stretching case bodies more than you need to, which is good news for brass life. The die is vented, so trapped air and excess lube have somewhere to go instead of denting a shoulder or dimpling a case. That venting detail is one of those small things you don't think about until you're pulling a cratered case out of a cheaper die.
Seating and Crimping Your 7mm WSM Loads
The Seater Die includes a bullet seater plug and a built-in roll crimper, so you can set bullet depth and crimp in the same stroke if your load calls for it. For a magnum like the 7mm WSM pushing heavier 7mm bullets at speed, having that crimp option on tap is handy, though plenty of folks run it crimp-free for precision work. Everything is machined from RCBS proprietary die steel and ships in the familiar green box.
To get rolling you'll still want the correct shell holder and your powder, primers, and bullets, since those aren't part of the die set. Pair these with quality 7mm WSM brass and a good press and you've got the heart of a solid reloading setup.
Key Specifications
- Manufacturer: RCBS
- Manufacturer Part Number: 31401
- UPC: 076683314017
- Caliber: 7mm WSM (7mm Winchester Short Magnum)
- Product Type: Full-Length 2-Die Set
- Die Series: Group A / Full Length
- Die Type: Sizer / Seater
- Dies in Set: 2
- Thread Size: 7/8"-14
- Die Steel: RCBS Proprietary Die Steel
- Crimp: Built-in roll crimper in seater die
- Country of Manufacture: United States
- Shipping Weight: 1.2 lbs
What’s Included
- Full-Length Sizer Die with Expander-Decapping Unit
- Seater Die with Bullet Seater Plug and built-in roll crimper
- RCBS green die storage box
Frequently Asked Questions
Will this RCBS 7mm WSM die set fit my press?
Yes, these dies are cut with the standard 7/8"-14 thread, which is the industry norm for reloading dies. That means they'll thread into common single-stage and turret presses from RCBS, Lee, Hornady, Lyman, and others. You just set them up and lock the rings down to your press.
Does the RCBS Full-Length 2-Die Set come with a shell holder?
No, the shell holder is not included with this set. You'll need to pick up the correct shell holder for the 7mm WSM case head separately. It's an inexpensive add-on that most handloaders already have on hand or grab alongside the dies.
Can I crimp my bullets with this 7mm WSM seater die?
Yes, the seater die has a built-in roll crimper, so you can seat and crimp in the same stroke if your load calls for it. Many reloaders running precision loads skip the crimp, while others use it for heavier magnum bullets or rounds that see rough handling. The choice is yours depending on how you set the die.
What does the full-length sizer die actually do to my brass?
It resizes the entire outside of the fired case back to SAAMI minimum dimensions, de-primes the spent primer, and runs the expander through to open the neck for a fresh bullet. Headspace is held to tight tolerances so the case body length stays consistent during sizing. The die is also vented to prevent dented shoulders from trapped air or excess lube.




Reviews
There are no reviews yet.