Description
Reloading for an AR-10, M1A, or any .308 that runs a snug chamber comes down to one thing: your rounds have to chamber and extract every single time. That's exactly what the RCBS 15503 small base set is built around. The sizer takes the case body and shoulder down a couple thousandths below standard full-length dimensions, which gives that extra bit of clearance semi-auto, pump, and lever actions want when they're hot, dirty, or running fast.
What the RCBS Small Base .308 Set Brings to the Bench
This is a two-die set covering .308 Winchester and 7.62 NATO brass. You get a Small Base Sizer with an Expander-Decapping Unit, so sizing and deprime happen in one stroke, plus a Regular Seater Die with a Seater Plug. The seater has a built-in roll crimper, letting you lock in the bullet as it seats. Want to seat without crimping? Just back the die off until the crimp ring no longer touches the case mouth. Both dies use the standard 7/8-14 thread, so they thread right into any common single-stage or progressive press.
Why Reloaders Reach for the RCBS 15503
The dies are machined from case-hardened steel and hand polished, with that RCBS finish meant to shrug off the abrasive wear sizing puts on tooling. The sizer is vented to let trapped air and excess lube escape, which keeps cases from getting dented during the full-length stroke. Large hex lock rings with hex-head set screws make setting and holding your adjustment quick and repeatable.
Picking the Right Tool for Your .308
Small base dies earn their keep when you're feeding gas guns, loading mixed or range-pickup brass, or dealing with a tight, match-cut chamber. They work the brass a touch harder than a standard full-length die, which is simply the trade-off for that bulletproof reliability. If you run a semi-auto .308 and want every round to chamber the first time and every time, this is the set that gets you there.
Key Specifications
- Manufacturer: RCBS
- Manufacturer Part Number (MPN): 15503
- UPC: 076683155030
- Caliber: .308 Winchester / 7.62 NATO
- Die Type: Small Base Sizer / Seater
- Number of Dies: 2
- Carbide: No
- Material: Case-hardened, hand-polished steel
- Thread Size: 7/8-14
- Series: Group A
- Shipping Weight: 1.2 lbs
What’s Included
- Small Base Sizer Die with Expander-Decapping Unit
- Regular Seater Die with Seater Plug (built-in roll crimper)
- Storage case
Frequently Asked Questions
Do I really need a small base die for my .308 semi-auto?
It depends on your rifle. Plenty of AR-10s, M1As, and Garands cycle just fine with standard full-length dies, but tighter match chambers and some semi-auto platforms want the extra clearance a small base die provides. A good test is to full-length size a few cases, pull the firing pin, and see if they chamber smoothly. If you get resistance or you're loading range-pickup and mixed brass, a small base die is cheap insurance.
What's the difference between this and a regular full-length .308 die?
A small base die is still a full-length sizer, it just takes the case body and base down a couple thousandths smaller than a standard die. That added reduction helps rounds drop into tight or fouled semi-auto chambers without hanging up. The trade-off is that it works the brass a bit harder, so case life can run slightly shorter than with standard sizing.
Can I use this RCBS set to seat bullets without crimping?
Yes. The seater die has a built-in roll crimper, but you can disable it by backing the die out until the crimp ring no longer engages the case mouth. That lets you seat bullets clean when you'd rather crimp in a separate step or skip it entirely.
Will these dies fit my press?
They should. Both dies use the standard 7/8-14 thread, which is what the vast majority of single-stage and progressive presses accept. If your press takes common RCBS, Lee, Hornady, or Lyman dies, this set threads right in.





Reviews
There are no reviews yet.