Description
The .30-30 Winchester has been feeding deer camps for well over a century, and it remains one of the most satisfying cartridges to reload on the bench. This RCBS Full-Length Die Set is the classic two-die setup for the job, pairing a full-length sizer with a bullet seater so you can take once-fired brass and turn it back into dependable, lever-ready ammo. Both dies use the standard 7/8-14 thread, so they'll thread right into just about any single-stage or turret press you already own.
What the RCBS .30-30 Two-Die Set Does on the Bench
The full-length sizer brings your fired case back down to SAAMI minimum dimensions, sizing the outside of the case, knocking out the spent primer, and expanding the neck to take a fresh bullet, all in one stroke. The die is vented to let trapped air and excess lube escape, which keeps you from denting or crushing those thin .30-30 cases. RCBS also holds headspace to tight tolerances here, so you aren't changing case body length while you size. That matters more than folks expect on a lever gun, since those cartridges feed at an angle out of a tubular magazine and like to be sized consistently.
Seating and Crimping with the RCBS 14601 Die Set
The seater die includes a bullet seater plug and a built-in roll crimp. For a tube-fed lever action, that crimp earns its keep. Rounds stack nose-to-primer in the magazine, and recoil can shove bullets deeper if they aren't locked in. The move most reloaders swear by is seating a flat-nose or round-nose bullet to the middle of its cannelure and rolling a light crimp into that groove. Go easy here, because a heavy crimp will buckle a .30-30 case in a heartbeat. If you'd rather not crimp, the die lets you seat bullets without it and lean on neck tension instead.
Every die in the set is properly hardened and hand-polished, which is the kind of fit and finish that's kept RCBS gear on reloading benches for decades. Note that this set uses RCBS Shell Holder #2, which is sold separately.
Key Specifications
- Manufacturer: RCBS
- Manufacturer Part Number: 14601
- UPC: 076683146014
- Caliber: .30-30 Winchester
- Product Type: Full-Length Die Set
- Series: Group A
- Number of Dies: 2
- Die Type: Sizer / Seater
- Crimp Style: Built-in roll crimp
- Thread Size: 7/8-14
- Shell Holder: Uses RCBS #2 (sold separately)
- Carbide: No
- Material: Hardened, hand-polished steel
What’s Included
- Full-Length Sizer Die with expander-decapping unit
- Seater Die with bullet seater plug and built-in roll crimper
Frequently Asked Questions
Do I need a shell holder with the RCBS .30-30 die set?
Yes. This set uses RCBS Shell Holder #2, and it is sold separately. You'll want to grab one before your first loading session, since the shell holder is what grips the case rim and raises it into the dies.
Will these dies work in my press?
They should. Both dies use the standard 7/8-14 thread, which is the industry-standard size for most single-stage, turret, and progressive presses. If your press takes common RCBS, Hornady, Lee, or Lyman dies, these will thread right in.
Can I seat bullets without crimping with the 14601 seater die?
You can. The seater die has a built-in roll crimp, but it can also be set up to seat bullets without applying any crimp if you'd rather rely on neck tension. For a tube-fed lever action though, a light roll crimp into the bullet's cannelure is the common choice to keep rounds from setting back under recoil.
Is this a carbide die set?
No, this is a standard hardened steel full-length set, not carbide. That means you'll want to lube your cases before sizing them. The sizer is vented to let trapped air and excess lube escape, which helps protect those thin .30-30 cases from denting.





Reviews
There are no reviews yet.