Description
The RCBS Expander/Decapping Assembly is one of those small parts that your whole reloading setup leans on. This is the 7mm version, part number 9809, and it does two jobs in a single pass through your sizing die: it punches out the spent primer and expands the case neck so your next bullet seats clean and straight. For a part that fits in the palm of your hand, it earns its keep every time you crank the press handle.
This unit is sized for the .284 bullet family, which covers a wide spread of popular 7mm cartridges. Owners of 280 Remington, 7mm Remington Magnum, 7mm STW, 7mm-08, 7×57 Mauser, and 7mm Weatherby brass will all find it at home in their RCBS dies. It's built from steel and precision machined to keep the expander ball running concentric, which is a big part of why your sized necks stay true and your runout stays low.
Why the 7mm 9809 Assembly Earns a Spot on the Bench
The assembly comes complete with the expander rod, expander ball, and decapping pin, so it's a full drop-in rather than a single loose piece. Setup is straightforward: thread it into your die with the pin protruding, run a lubed case up, and lock the nut down while the case is seated to keep everything centered. RCBS recommends setting the decap pin to extend roughly 0.400 inch from the bottom of the die for reliable primer removal.
Keeping a Spare 9809 Decapping Unit Handy
Decapping pins and expander rods are the parts most likely to bend or snap if a case has a crimped primer pocket or a bit of debris sneaks in. Having an extra 9809 on the shelf means a damaged pin doesn't shut down your loading night. Since these are the same factory units RCBS ships inside their die sets, you get a correct fit and the backing of their Limited Lifetime Warranty. Note that these are made to fit RCBS dies.
Key Specifications
- Manufacturer: RCBS
- Manufacturer Part Number: 9809
- UPC: 076683098092
- Caliber: 7mm / .284
- Type: Expander-Decapping Unit
- Material: Steel
- Fits: 280 Rem, 7mm Rem Mag, 7mm STW and other 7mm cartridges
- Compatibility: RCBS dies
- Quantity: 1
- Warranty: RCBS Limited Lifetime Warranty
- Country of Origin: United States
What’s Included
- RCBS 7mm Expander/Decapping Assembly (Part 9809) with expander rod, expander ball, and decapping pin
Frequently Asked Questions
What cartridges does the RCBS 7mm 9809 expander/decapping assembly work with?
It's made for the .284 bullet family, so it covers a broad range of 7mm cartridges. That includes 280 Remington, 7mm Remington Magnum, 7mm STW, 7mm Weatherby Magnum, 7mm WSM, 7mm-08, and 7×57 Mauser, among others. If you're reloading a bottleneck 7mm case, this unit most likely fits the bill.
Will this decapping unit fit non-RCBS dies?
This is a factory RCBS replacement unit designed specifically for RCBS dies. If you run another brand of dies, you'll want to check with that manufacturer for the correct part. For RCBS owners, it's the same unit the company ships inside its die sets.
What exactly does this assembly do during reloading?
It handles two jobs in one stroke of the press. The decapping pin pushes the fired primer out of the pocket, while the expander ball opens the case neck back up so the next bullet seats properly. On bottleneck rifle cases, both happen as you run the brass through your sizing die.
How do I set up and center the 9809 unit?
Thread the unit into your die with the pin sticking out, then run a lubed case up into the die and lock the nut down while the case is still seated to keep it centered. RCBS suggests setting the decap pin to extend about 0.400 inch from the bottom of the die. If it ends up off-center, loosen the nut and repeat the process.





Reviews
There are no reviews yet.