Description
When you catch a bad powder charge or just need to swap out a bullet, the RCBS 9440 Standard Bullet Puller is the quiet, no-drama way to take a round apart. It threads right into your press like a standard die and uses a collet that clamps down on the bullet, then the case pulls free as you lower the ram. Think of it like a draw collet on a lathe grabbing hold and letting go on command. For anyone pulling jacketed bullets in any kind of volume, it beats whacking an inertia hammer round after round.
How the RCBS Bullet Puller Works on Your Press
The body uses the common 7/8-inch-14 thread, so it drops into any single-stage press with that thread, and it plays nice with compatible turret setups too. Setup is simple: seat the collet, run a cartridge up into it with the ram, snug the T-handle down to grip the bullet, then lower the ram to separate the two. Loosen the handle and the bullet drops free. Folks who run large batches, like a few hundred rounds of .223 or crimped surplus, tend to appreciate how much faster and cleaner this is compared to the hammer method. One tip from experienced reloaders: if you're fighting a heavy crimp, bump the bullet a touch deeper with a seating die first and it'll release easier.
What You Need to Run the RCBS 9440
Here's the important part. This is the puller body only. It does not ship with any collets, and you'll want a caliber-specific collet for whatever you're pulling. The collet is what actually grabs the bullet, so matching it to your bullet diameter matters. It's built for centerfire jacketed bullets and is not meant for rimfire cartridges. It's also not compatible with the Summit Press. Made in the USA with the kind of solid build RCBS has a long reputation for, this is a tool that'll serve a bench for decades.
Key Specifications
- Manufacturer: RCBS
- Manufacturer Part Number: 09440
- Model: Standard Bullet Puller without Collet
- UPC: 076683094407
- Type: Bullet Puller w/o Collet
- Caliber: Multi-Caliber
- Thread Size: 7/8-inch-14
- Compatible With: Single-Stage or Turret Press with 7/8-14 Thread
- Function: Pulls Jacketed Bullets
- Material: Metal
- Finish: Silver
- Length: 5.95 in
- Quantity: 1
- Country of Origin: Made in USA
What’s Included
- RCBS Standard Bullet Puller body (model 9440)
- Instruction manual
Frequently Asked Questions
Does the RCBS 9440 come with a collet?
No, this is the bullet puller body only. You'll need to buy a caliber-specific collet separately for whatever bullet diameter you plan to pull. The collet is the part that actually grips the bullet, so match it to your project before your first pull.
What presses will the RCBS Standard Bullet Puller fit?
It uses the standard 7/8-inch-14 thread, so it threads into any single-stage press with that thread, and it works in compatible turret presses as well. It is not compatible with the Summit Press. Many reloaders like to dedicate a spare hole on a turret or a cheap extra single-stage press just for pulling duty.
Will the RCBS bullet puller work on rimfire or lead bullets?
It's made for centerfire cartridges with jacketed bullets and is not for use with rimfire. Soft, non-jacketed lead bullets can distort under the collet's grip, so it's best suited to jacketed projectiles. For occasional one-off pulls on any cartridge, a kinetic hammer puller is the more flexible choice.
Is a collet puller better than a kinetic hammer puller?
For anything beyond a handful of rounds, the collet style is a big time saver since you're not hammering each cartridge against the floor. It screws into your press and pulls bullets with a simple tighten-and-lower motion. If you're only pulling a round or two now and then, a kinetic puller is quicker to grab, but for batch work the RCBS collet system wins.



Reviews
There are no reviews yet.