Description
Every reloader eventually loads a round they need to take apart, whether it's a seating depth that slipped, the wrong powder charge, or a batch of surplus ammo worth pulling down for the components. This RCBS Bullet Puller Collet, part number 9428, is the piece that makes that job clean. Sized specifically for .32 caliber and 8mm bullets (.323 diameter), it fits inside the RCBS Standard Bullet Puller body and clamps onto the bullet so you can draw it straight out of the case.
The appeal here is control. Rather than hammering rounds apart and risking a dented bullet or a bent case mouth, the collet grips the bearing surface and lets the press do the work. Reloaders who run it report that it pulls bullets safely with no scratches, even on factory-crimped brass, which means you can reuse both the bullet and the case when the powder gets dumped back out. It's a favorite for taking down 8×57 Mauser surplus and anything else in the family.
What the .32 / 8mm Collet Handles
This collet covers a broad slice of the .323 bullet world. Think 8mm Mauser (8×57 IS), 8mm Remington Magnum, .325 Winchester Short Magnum, and similar cartridges built on the same bullet diameter. Some folks have even pressed it into service on .303 British with good results, since it's grabbing the bullet rather than the case.
Fitting the Collet to Your RCBS Standard Bullet Puller
Setup is quick. Thread your bullet puller die into the press with this collet installed, raise the ram to seat the cartridge, snug the collet down onto the bullet, then lower the ram to separate the two. The puller body uses standard 7/8-14 threads, so it works with just about any single-stage press on the bench. Keep in mind this listing is the collet only and is meant to pair with the RCBS Standard Bullet Puller body rather than replace it. If you already own the puller and just need to add .32/8mm capability, this is the part that gets you there.
Key Specifications
- Manufacturer: RCBS
- Manufacturer Part Number (MPN): 9428
- UPC: 076683094285
- Product Type: Bullet Puller Collet
- Caliber/Gauge: .32 Cal / 8mm (.323)
- Compatible With: RCBS Standard Bullet Puller
- Thread: 7/8-14 (puller body)
- Press Type: Single Stage
- Material: Steel / Metal
- Finish: Silver / Gray
- Length: 2.4 in
- Quantity: 1
- Country of Origin: USA
What’s Included
- 1 RCBS Bullet Puller Collet, .32 Cal / 8mm (MPN 9428)
Frequently Asked Questions
Does this RCBS collet come with the bullet puller, or is it the collet only?
This listing is the .32 caliber/8mm collet by itself. It's designed to install inside the RCBS Standard Bullet Puller body, which is sold separately. If you already own that puller, this collet simply adds .32/8mm capability to your setup.
What cartridges will the .32 Cal / 8mm collet work with?
It's built for bullets in the .323 diameter family, so it covers 8mm Mauser (8×57), 8mm Remington Magnum, .325 Winchester Short Magnum, and similar rounds. Because it grips the bullet rather than the case, reloaders have also used it successfully on cartridges like .303 British.
Will the RCBS Bullet Puller Collet damage my bullets or brass?
No, that's the main advantage over inertia or hammer-style pullers. The collet clamps onto the bullet and draws it straight out, so both the bullet and the case come out clean for reuse. Users report pulling bullets with no scratches, even from factory-crimped brass.
How do I use the collet with my press?
Thread the bullet puller die into your press with this collet installed, then raise the ram to bring the cartridge up into the die. Tighten the collet down onto the bullet, then lower the ram to pull the bullet free from the case. The puller body uses standard 7/8-14 threads, so it fits virtually any single-stage press.


Reviews
There are no reviews yet.