Description
The Nosler RDF Match 6mm (.243) 105gr HPBT is a competition-focused bullet built for handloaders who care about every fraction of an inch at distance. RDF stands for Reduced Drag Factor, and the whole design is aimed at squeezing the most downrange performance out of your 6mm. With a G1 BC of 0.571 and a G7 of 0.280, this is one of the flatter shooting match projectiles you'll find in the .243 world, which translates to less holdover and less wind call guessing when the shot gets long.
The secret behind this bullet is a combination of a compound ogive and a long, drag reducing boat tail. The compound ogive blends tangent and secant profiles, which makes the bullet more forgiving on seating depth and easier to tune to your chamber. Weighing 105 grains with a 0.243 diameter and a 1.250 inch overall length, it carries a sectional density of 0.254 and runs on a copper jacket over a lead core.
Why the RDF 6mm 105gr Saves You Time at the Bench
One of the standout features here is the meplat. Nosler closes the tip tight at the factory, giving these the smallest and most consistent meplats of any non-tipped match bullet in their lineup. In plain terms, that means no pointing and no trimming tips to chase uniformity. You pull them out of the box and load them, which is a real time saver if you run big volume for PRS or F-Class.
Running the Nosler RDF Match 6mm in Your Rifle
These need a minimum 1-8 inch twist to stabilize properly, so check your barrel before you commit a big load session to them. They're a natural fit for 6mm Creedmoor, 6XC, 6mm Dasher, and similar high performance 6mm cartridges where handloaders want maximum BC without the extra prep. Packaged 100 to a box, they're made in the United States and built for target and competition use where consistency wins matches.
Key Specifications
- Manufacturer: Nosler
- Manufacturer Part Number: 53410
- UPC: 054041534109
- Caliber: 6mm (.243)
- Bullet Diameter: 0.243 in
- Bullet Weight: 105 grain
- Bullet Type: Hollow Point Boat Tail (HPBT)
- Series: RDF (Reduced Drag Factor)
- Ballistic Coefficient (G1): 0.571
- Ballistic Coefficient (G7): 0.280
- Sectional Density: 0.254
- Overall Length: 1.250 in
- Cannelure: No
- Recommended Twist: Minimum 1-8 in
- Quantity: 100 Per Box
- Country of Manufacture: United States
What’s Included
- 100 Nosler RDF Match 6mm (.243) 105gr HPBT bullets
Frequently Asked Questions
What twist rate do I need to stabilize the Nosler RDF 6mm 105gr?
Nosler lists a minimum 1-8 inch twist for this 105 grain RDF. Faster twists like 1-7.5 will also work well and give you a little extra stability margin. If your barrel is slower than 1-8, these likely won't stabilize reliably, so verify before loading a batch.
Do I need to trim or point the tips on these RDF bullets?
No. Nosler closes the meplat tight at the factory, and these carry the smallest, most consistent meplats of any non-tipped match bullet in their line. That means you can skip the pointing die and tip trimming and load them straight out of the box.
What cartridges is the RDF Match 6mm 105gr good for?
This bullet is a popular choice for high-performance 6mm cartridges like 6mm Creedmoor, 6XC, 6mm Dasher, and 6BRA. Its high BC and forgiving compound ogive make it a strong pick for PRS, F-Class, and long range target work where you want flat trajectory and minimal wind drift.
Why does the compound ogive matter on the Nosler RDF?
The compound ogive blends tangent and secant shapes, which makes the bullet less sensitive to seating depth. That gives you more room to tune your load without chasing the lands as precisely, which simplifies workup. It also contributes to the sleek, high-BC profile that makes the RDF shoot flat.




Reviews
There are no reviews yet.