Description
Sporting clays means a lot of rounds downrange in a single outing, and a stiff factory pad starts wearing on you by the back half of the course. The Kick-Eez Dual Action Sporting Clay Pad is built to take that sting out. It uses two layers of Sorbothane, a proprietary polymer that absorbs shock and vibration instead of bouncing it straight back into your shoulder. The recoil energy gets pushed out the sides of the pad rather than back at you, which means less flinch, a quicker recovery between shots, and more comfort when you're calling for a lot of targets.
What Makes the Dual Action Different
Regular Kick-Eez pads run a single layer of 70 durometer Sorbothane. The Dual Action stacks a softer 60 durometer layer against the baseplate underneath the firmer material, so recoil waves pass through two different densities and get knocked down further. That layered setup shaves a few extra percent of felt recoil compared to the standard pads, which is exactly what folks sensitive to kick are after during long sessions.
Cut for the Low-Gun Stance
The sporting clay profile has its heel tilted at a 45 degree angle, which makes mounting from a low-gun ready position smoother and more consistent. That angle helps the gun slide up into your shoulder pocket without catching on a vest or shirt, so your mount stays repeatable target after target. This medium measures 5-1/4 inches long by 1-7/8 inches wide at 1-1/8 inches thick, with standard 3-1/8 inch hole spacing that fits a wide range of stocks.
Grinding the Kick-Eez Pad to Fit
This is a grind-to-fit pad, so it screws onto your buttstock and sands down to match your stock and your preferred length of pull. There are no air pockets or metal shims inside, just solid Sorbothane, which gives you more room to grind and a more consistent mount every time. Made in the USA, finished in matte black for a clean non-glare look on wood or synthetic stocks.
Key Specifications
- Manufacturer: Kick-Eez
- Manufacturer Part Number: DA 202-10-M-B
- UPC: 730412001578
- Style: Dual Action Sporting Clay
- Size: Medium
- Thickness: 1-1/8"
- Length: 5-1/4"
- Width: 1-7/8"
- Hole Spacing: 3-1/8"
- Material: Sorbothane (dual-layer 60 and 70 durometer)
- Color: Black
- Mounting: Screw-on, grind-to-fit
- Country of Origin: Made in USA
What’s Included
- Kick-Eez Dual Action Sporting Clay recoil pad (Medium, 1-1/8")
Frequently Asked Questions
What makes the Dual Action version different from a standard Kick-Eez pad?
The Dual Action uses two layers of Sorbothane instead of one. A softer 60 durometer layer sits against the baseplate under the firmer 70 durometer material, so recoil passes through two densities and gets reduced further. That layering cuts felt recoil by roughly an extra four to six percent over the standard single-layer pads, which is noticeable on high-volume days.
Do I have to grind this Kick-Eez sporting clay pad to install it?
Yes, this is a grind-to-fit pad that screws onto your buttstock and sands down to match your stock outline and desired length of pull. Since Sorbothane is a polymer and not rubber, use a belt or disc sander around 1700 to 2500 RPM, start with 80 to 120 grit, and finish with 220 grit while rotating the pad to avoid heat buildup. Skip high-speed tools like a Dremel, and round the heel, toe, and sides when you're done.
What's the point of the angled heel on the sporting clay profile?
The sporting clay pad has its heel tilted at a 45 degree angle, which is built for shooting from a low-gun ready position. That angle helps the gun slide cleanly into your shoulder pocket without snagging on your vest, giving you a smoother and more repeatable mount as you call for targets.
Will this medium pad fit my shotgun?
It uses standard 3-1/8 inch hole spacing, which lines up with a wide range of shotgun stocks. Because you grind it down to your own stock shape, the fit is custom to your gun once it's installed. For synthetic stocks, a gunsmith is worth considering for a clean mount.





Reviews
There are no reviews yet.