Description
Talley kept this one simple and solid. Instead of a separate base and ring setup, the ring and base are machined as a single unit, which takes the guesswork out of alignment and gives you a stronger platform that holds zero round after round. This set is cut for Browning X-Bolt long and magnum action rifles, runs a 30mm tube diameter, and sits at the low height for a clean, close-to-the-bore sight picture. The Burnt Bronze finish is the Hell's Canyon look that pairs nicely with X-Bolt rifles wearing that same coloring.
What the 20 MOA Does on This X-Bolt Mount
The standout feature here is the 20 minutes of angle built directly into the rings. That forward cant gives your scope extra elevation travel baked in, so when you're reaching way out there you've got more usable adjustment left in the turret instead of running out of dial. If long-range work or heavier magnum loads are on your plate, that built-in slope earns its keep.
Fit and Build of the Talley Burnt Bronze Rings
These are fully CNC machined from lightweight aircraft-grade aluminum to tight tolerances, so they arrive rigid and ready to bolt on with no lapping required. The mount attaches to the receiver using 6-48 screws, and the low rings run roughly .440 inch at the front and .546 inch at the rear. Being one piece, there's no ring-to-base joint to work loose or drift out of alignment over time.
Picking the Right Talley X-Bolt Scope Mount
This particular set is the long/magnum action version, so double check your X-Bolt before ordering since short and super short actions use a different mount. The low height works best with smaller objective scopes; if you're running a big bell up front you may want to size up to medium or high to clear the barrel. For a standard hunting optic on a long or magnum X-Bolt, this low 30mm set keeps everything tight, light, and locked down.
Key Specifications
- Manufacturer: Talley
- Manufacturer Part Number: HC730735LM
- UPC: 876430002828
- Fits: Browning X-Bolt Long/Magnum Action
- Tube Diameter: 30mm
- Ring Height: Low
- Built-In MOA: 20 MOA
- Finish/Color: Burnt Bronze (Hell's Canyon)
- Material: Aircraft-Grade Aluminum
- Construction: One-Piece Integrated Ring and Base, CNC Machined
- Mount Height: 0.440 in Front / 0.546 in Rear
- Mounting Screws: 6-48
- Lapping: Not Required
- Made In: USA
- Shipping Weight: 0.235 lb
What’s Included
- One pair of Talley one-piece X-Bolt scope mounts (ring and base combo)
- Mounting hardware (6-48 screws and ring screws)
Frequently Asked Questions
Will this Talley mount fit any Browning X-Bolt?
This set is cut specifically for Browning X-Bolt rifles with long and magnum length actions. Short and super short action X-Bolts use a different mount, so confirm your action length before ordering. Once you've matched the action, it bolts right to the receiver with the included 6-48 screws.
What does the 20 MOA do on this X-Bolt scope mount?
The 20 minutes of angle is machined into the rings as a forward cant, giving your scope extra built-in elevation. That means more usable turret travel when you're dialing for long distances or shooting heavier magnum loads. It's a nice advantage if extended-range work is your thing.
Do I need to lap these Talley rings before mounting a scope?
No. Because the ring and base are machined as a single unit from aircraft-grade aluminum to tight tolerances, these arrive aligned and ready to install right out of the box. Lapping isn't needed and isn't recommended.
Will a low ring height clear my scope on an X-Bolt?
Low rings keep the optic close to the bore, which works great with standard and smaller objective scopes. If you're running a large objective bell, measure your clearance, since you may want to step up to medium or high rings instead. For most typical hunting scopes, the low height gives a clean, comfortable sight picture.





Reviews
There are no reviews yet.